Re: CBot Marlin to 'mainline' marlin 1.0 or 1.1
Here's the Configuration.h that's loaded in now - To allow me to turn on the bed heater and actually let it heat (Takes longer for the actual bed to get hot than the temp indicated on the display and...
View ArticleRe: CBot Marlin to 'mainline' marlin 1.0 or 1.1
Did not see anything in your configuration.h that looks off. Let me get some more information. lets say you just turned the 3D Printer on what is the temperatures reading on the display before you...
View ArticleRe: A problem with Atom
I did find Git-Bash, but it's external to Atom. I thought it was a "package".
View ArticleRe: CBot Marlin to 'mainline' marlin 1.0 or 1.1
Since it's printing now and has been for about three hours, the temp of hotend 1 (which is not being used or heated right now) is a bit off, but I believe the typical starting temps are in the 20C...
View ArticleRe: CBot Marlin to 'mainline' marlin 1.0 or 1.1
PID is a calibrated, However I use the " Ultimaker " default on my hotend // FIND YOUR OWN: "M303 E0 C8 S190" to run auto tune on the hot-end at 190 degrees C for 8 cycles. #define DEFAULT_Kp 22.2...
View ArticleRe: A problem with Atom
Roxy thank you very much for your help. It turns out that I had an old version of Git and I have upgraded it now and it started working. Sorry about my lack of knowledge I will work to improve it....
View ArticleNo power to Z-axis in Marlin with TCM 2130 Drivers.
I'm stuck... I am sure the problem is something simple that I am missing, I recently switched from Repetier to Marlin to take advantage of the TCM 2130 Drivers. All of my electronics (Arduino...
View ArticleFree xy problem (delta printer)
If I go to prepare-> move axis I am only getting the option to Free XY. if I select this option the carriages move up and ignore the endstops. Previously I was able to move the x and y axis...
View ArticleFree xy problem (delta printer)
If I go to prepare-> move axis I am only getting the option to Free XY. if I select this option the carriages move up and ignore the endstops. Previously I was able to move the x and y axis...
View ArticleFree xy problem (delta printer)
If I go to prepare-> move axis I am only getting the option to Free XY. if I select this option the carriages move up and ignore the endstops. Previously I was able to move the x and y axis...
View ArticleFree xy problem (delta printer)
If I go to prepare-> move axis I am only getting the option to Free XY. if I select this option the carriages move up and ignore the endstops. Previously I was able to move the x and y axis...
View ArticleFree xy problem (delta printer)
If I go to prepare-> move axis I am only getting the option to Free XY. if I select this option the carriages move up and ignore the endstops. Previously I was able to move the x and y axis...
View ArticleFree xy problem (delta printer)
If I go to prepare-> move axis I am only getting the option to Free XY. if I select this option the carriages move up and ignore the endstops. Previously I was able to move the x and y axis...
View ArticleRe: No power to Z-axis in Marlin with TCM 2130 Drivers.
have you double checked all the jumpers from the stepsticks to the AUX2 and AUX3 connectors on the RAMPS? Since your X/Y work and your Z does not I wonder if the lines from the Z stepstick are the...
View ArticleUsing a BLTouch and a Z axis min microswitch?
I'm using Marlin 1.1.7 and plan to go to 1.1.8. I read the config files and have an understanding of how to configure for using a BLTouch. I actually connected it free standing and compiled the code...
View ArticleMenu scrolling, underlined vs light background
Reading through the config files for 1.1.7 it states that using reverse video for highlighting the option when scrolling the through the menus is more CPU intensive then using underling. So I left it...
View ArticleRe: CBot Marlin to 'mainline' marlin 1.0 or 1.1
Look at your 1.1-Configuration.h found these #define FIX_MOUNTED_PROBE // You Need this line #define Z_MAX_POS 2350 // this must be an error You have two LCD defined is this a error #define ULTRA_LCD...
View ArticleRe: Odd inductive sensor triggering issue - z axis min
The offset is set to 4 since that's the offset between the nozzle and the probe but it had no effect either way.
View ArticleRe: CBot Marlin to 'mainline' marlin 1.0 or 1.1
Thanks got the catch on the max Z height - that was a typo. Was supposed to be 235. Yes, 'REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER' was the correct one. After wading through again, I discovered...
View ArticleG33 gives not correct nozzle height wenn leveled
Hi all, I go tan Anycubic Linear Plus. When I calibrate the printer with PROBE_MANUAL, everything is fine. It is a lot of work but it is doing well. If I define BILINEAR, the problem starts. If I do a...
View Article