Re: Hacking Marlin to control a heated enclosure
i like your idea and that was the direction i was leaning but i agree... it needs to be able to be set to bang like as if it were a heater bed configuration....
View ArticleRe: Hacking Marlin to control a heated enclosure
Probably this should be implemented so it can be controlled with GCode. And the code should wire up the M109 logic to wait for the enclosure to reach temperature. This is a good idea and will have...
View ArticleRe: CBot Marlin to 'mainline' marlin 1.0 or 1.1
I might have something else that's not right in the firmware. Spent a little time over the last two evenings swapping out the hot end heaters, throat cooling fan and re-wiring the bed for 24V and...
View Article1.1.8 wont upload
I downloaded the latest version to try out the mesh bed leveling but i can not get it to upload to my machine. When i click upload it stops in the "SanityCheck.h" file on the line that reads...
View ArticleMKS Gen V1.4 Motors not working
Hi All, I've just made the upgrade from an MKS Base to an MKS gen V1.4. I have A4988 drivers installed in each of the slots and I uploaded the exact same firmware that I was using on my MKS base to...
View ArticleRe: Using a BLTouch and a Z axis min microswitch?
And the answer to the question is... Yes. You can do this. Had both working under 1.1.7. Have both working under 1.1.8.
View ArticleWrong Probe Status
Hey there, I am using Marlin 1.1.8 on my Anet A8 Prusa i3 clone with an inductive sensor for ABL. For some reason the probe status sometimes gets inversed after finishing or aborting prints. When I...
View ArticleIs 1.1.7 (and 1.1.8) too big for Creality Melzi board??
Hello all, Trying to upgrade my CR-10 to 1.1.7 and it wont compile when I enable all the features I want. And I get a warning that “Text” will not fit into text region then the linker throws a fault....
View ArticleRe: MKS Gen V1.4 Motors not working
I find it doubtful that the MKS Base and MKS Gen would have the same pins configuration. You should start with a bare firmware and set it up from scratch.
View ArticleRe: 1.1.8 wont upload
What are those lines set to? It seems to be saying that you have setup the x/y axis to be operating outside the size of the bed. what size is your bed, what size does Marlin think your bed is.. how...
View ArticleRe: Is 1.1.7 (and 1.1.8) too big for Creality Melzi board??
Not sure on this one, but the error leads me to think that the text that is displayed on the LCD is larger than the LCD is capable of displaying. I very much doubt its what your thinking tho, as I can...
View ArticleRe: 1.1.8 wont upload
If you post your configuration.h will have a look see what is going on. Need the Version of marlin 1.1.X you are working with. May also help to know What 3D Printer you are working to install Marlin...
View ArticleRe: 1.1.8 wont upload
I updated my Arduino to the latest version and it seemed to get rid of a lot of the compiling errors. Have other problems now but i will make a new thread for that.
View Article1.1.8 can not travel past XY 0
I am trying to get 1.1.8 tuned in but its been one struggle after another. Spent many hours today on this problem and cant seem to get past it. My setup is AtMega2560 in a Folgertech Cloner machine....
View ArticleRe: Is 1.1.7 (and 1.1.8) too big for Creality Melzi board??
Hello JustSumGuy, Thanks for the quick response... So I got 1.1.8 (also worked with Marlin 1.1.7) compiled and uploaded to my Creality CR10 Melzi board with full LCD support and it appears to be...
View ArticleRe: 1.1.8 can not travel past XY 0
Not a developer but can you move your limit switches to coincide with the position you want??? if not I ran into a similar thing while trying to zero my z height. Im sure there is a better/safer...
View ArticleRe: 1.1.8 can not travel past XY 0
I tried commenting out the minimum position limits and it still would not travel past 0.
View ArticleRe: Wrong Probe Status
I have a similar problems to this on my hypercube evo as well, but still no answers :S
View ArticleSD Card Menu on CR-10S
I have replaced the original firmware on my CR-10S with Marlin 1.1.7. I have gotten all the settings the way I want them except the SD card menu. On the original firmware, there were Change,...
View Article