Re: Is it necessary to enable PID for the heat bed?
Using bang bang on the heat bed is not usually that bad, worth a try but keep in mind if you use ABS you might get some issues due to warping IF the bed takes wild swings in temp. Useing a thermal...
View ArticleRe: Marlin 2.x help or other recommendations?
Actually... The CoreXY machines should not be much different than the normal Cartesian machines from a computational perspective. Probably that quote is from this thread: [github.com] That is where we...
View ArticleRe: CBot Marlin to 'mainline' marlin 1.0 or 1.1
I see your delima with so completely different configuration.h files. I have been working with Marlin 1.1.x files where they are really similar to each other.
View ArticleRe: CBot Marlin to 'mainline' marlin 1.0 or 1.1
Look at your 1.1-Configuration.h found these #define FIX_MOUNTED_PROBE // You Need this line #define Z_MAX_POS 2350 // this must be an error You have two LCD defined is this a error #define ULTRA_LCD...
View ArticleRe: Odd inductive sensor triggering issue - z axis min
The offset is set to 4 since that's the offset between the nozzle and the probe but it had no effect either way.
View ArticleRe: CBot Marlin to 'mainline' marlin 1.0 or 1.1
Thanks got the catch on the max Z height - that was a typo. Was supposed to be 235. Yes, 'REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER' was the correct one. After wading through again, I discovered...
View ArticleRe: CBot Marlin to 'mainline' marlin 1.0 or 1.1
This is sometimes done in the Slicer. As in my case it primes the extruder before it starts to print. I print a couple skirts to keep it away from the print. And usually get bothered by it a grab it...
View Article1.1.8 Homing correctly but not when running print
Hello, i decided to update my firmware today in my CR-10S to accommodate a Z probe in the coming days so, after downloading and following a few youtube videos the printer started with the new marlin...
View ArticleRe: 1.1.8 Homing correctly but not when running print
Just a thought, but maybe you have two problems working in tandem. lets say the motor direction is reversed AND the end stop is set to the opposite end.. in that case I think it would home but then...
View ArticleRe: 1.1.8 Homing correctly but not when running print
Well I have seen this as the problem so I tried to change the home from -1(min) to 1(max) but then I get an error for my endstops need to be wires to max when there wired to min as standard would this...
View ArticleRe: 1.1.8 Homing correctly but not when running print
I really don't know your printer layout but I believe when you set the firmware to end stops max or min, your telling the firmware where the end stop is physically. Not just where its plugged in on...
View ArticleRe: Is it necessary to enable PID for the heat bed?
Thanks a lot for your answers!!!! (:D
View ArticleRe: 1.1.8 Homing correctly but not when running print
JustSumGuy Thank you for your help turns out it was in fact the wires to the motors needed to be reversed thank you for the idea (tu):)-D
View ArticleDisabling Z home double bumping in Marlin 1.1.8
Since using a piezo sensor, I want to disable the double bump feature of Z homing. I've already increased the double bump speed (piezo requires certain speed to make sure it triggers) by setting...
View ArticleRe: 1.1.8 Homing correctly but not when running print
QuoteOben221 JustSumGuy Thank you for your help turns out it was in fact the wires to the motors needed to be reversed thank you for the idea (tu):)-D Glad to help :)
View ArticleRe: CBot Marlin to 'mainline' marlin 1.0 or 1.1
Had a strange one this evening - I set the bed to heat up to 80C and after a little bit, set the hot end to heat up to 235C, and after a fairly short amount of time, I got a 'Thermal Runaway' message,...
View ArticleA problem with Atom
I'm using an editor/compiler called Atom. I've recently downloaded Marlin 1.1.8. I am having difficulty with the platformio.ini file that I do not know how to fix. In the new file there is a new...
View ArticleRe: CBot Marlin to 'mainline' marlin 1.0 or 1.1
If you post your new configuration.h file will have another look see if anything jumps out at me.
View ArticleRe: A problem with Atom
I think you need to install Git-Bash. I forget why that is necessary now but it has to do with some repository that needs to be checked out.
View Article