Re: CBot Marlin to 'mainline' marlin 1.0 or 1.1
I'm open to any tips/tricks/suggestions anyone has to offer - my first hurdle is with compiling though. Initially, I compiled the latest version of 1.0 with all the settings from the configuration.h...
View ArticleHeating problem during printing
Hi, I am using Marlin 1.1.8 Heating is just fine when the printer is idle and I tuned the PID parameters. I also tried extruding a quite amount of plastic and temperature dropped just 4 C before...
View ArticleRe: CBot Marlin to 'mainline' marlin 1.0 or 1.1
You can also use '#define MOTHERBOARD BOARD_RAMPS_14_EFB'
View ArticleTrying to setup a BLTouch and failing
Happy New Year! I've been banging my head against the wall trying to get my BLTouch setup. This is what the terminal on Octoprint outputs when I start up: QuoteRecv: Error:STOP called because of...
View ArticleRe: Heating problem during printing
What I realized, by the way, pwm value of hotend heater is maximum 62 in M105 messages.
View ArticleRe: Thermistor selection Marlin 1.1.8
I found it!!!! I don't think type 1 would have been very accurate, would have worked but been out a fair bit much like the type 5 I have been using. now to work out how to put this info into marlin.....
View ArticleRe: Thermistor selection Marlin 1.1.8
Can someone plz take a look at this and tell me if I did this right? I attached an Excel sheet of the info below as formatting doesn't look right on a cut paste from Excel.... The table creator I...
View ArticleRe: CBot Marlin to 'mainline' marlin 1.0 or 1.1
Tried changing it to '14_EFB' and still getting the compile errors. Looked further up the error and this is what it's complaining about: SanityCheck.h:1065: error: #error "TEMP_SENSOR_2 shouldn't be...
View ArticleRe: CBot Marlin to 'mainline' marlin 1.0 or 1.1
That would be correct. I have a configuration.h setup file for Dual extruders but have never used it. Take a look see. [attachment 101117 Configuration.h] Have been using this program to compare...
View ArticleOdd inductive sensor triggering issue - z axis min
So, if I home through the smart controller display in the "prepare" menu, everything works normally and correctly. Everything homes then I can bed run the "bed leveling" and that works normally as...
View ArticleMarlin 2.x help or other recommendations?
Hi guys, I've just built a corexy machine from scratch and am in the process of doing the electronics. I started off with an arduino mega and ramps board running marlin 1. And all went well for...
View ArticleRe: Marlin 2.x help or other recommendations?
I doubt you want to hear what I am going to say but its just my opinion :) I ran ramps for a while on my little cube, it burned up after a few months while running a tiny hotbed, its limited and a...
View ArticleRe: Odd inductive sensor triggering issue - z axis min
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle] you need to set this to 10
View ArticleRe: Marlin 2.x help or other recommendations?
Thanks for your advice, it's helped a tonne! (tu) My original plan (naively) was to buy the mega/ramps/screen bundle cheap and set the whole thing up using that (incase I fried it) then switch the...
View ArticleRe: Marlin 2.x help or other recommendations?
If you want to use the Atmega-2560 there is no reason not to use the Bugfix-v1.1.x branch. The feature set is identical with the Bugfix-v2.0.0 branch. We are using Re-ARM boards with RAMPS boards as...
View ArticleRe: CBot Marlin to 'mainline' marlin 1.0 or 1.1
Just a quick update - I finally got somewhere. After digging around, I realized the reason it was complaining about the temp sensors was because I hadn't configured sensor 1 so it was still set to...
View ArticleRe: Thermistor selection Marlin 1.1.8
will the following work? I plan to replace thermistortable_8.h with this and adjust a few other files to reflect the different thermistor name that table 8 will now be. /** * Marlin 3D Printer...
View ArticleClik here to view.
Re: Marlin 2.x help or other recommendations?
QuoteRoxy If you want to use the Atmega-2560 there is no reason not to use the Bugfix-v1.1.x branch. The feature set is identical with the Bugfix-v2.0.0 branch. I don't think the atmega2560 is...
View ArticleIs it necessary to enable PID for the heat bed?
I'm trying to upload the new marlin firmware to my board but I'm getting an error:- Arduino: 1.8.5 (Windows 7), Board: "Arduino/Genuino Mega or Mega 2560, ATmega2560 (Mega 2560)"...
View ArticleRe: Is it necessary to enable PID for the heat bed?
I have been 3D Printing without #define PIDTEMPBED on 2 3D Printer for over a year now with not side effects.
View Article