Re: 1.1.7 after auto home / bed leveling raises Z 10mm:(
I'm going to try this as soon as I get some prints out the way. Thank you for all of your help Roxy.
View ArticleMotors Off after 2 mins ?
I've just upgraded from Marlin 1.1.0-RC3 to 1.1.8 and I'm getting some sort of timeout occuring. I home all axis and then after approx 2 mins the motors switch off and the display shows flashing '?'...
View ArticleThermistor/LCD Display shows opposite change in temperature
Has anyone ever experience an opposite temperature change readout from a thermistor connected to Ramps 1.4 running current Marlin? Marlin 1.1.8 Arduino Mega 2560 R3 Ramps 1.4 12864 LCD w/SD Card...
View ArticleRe: Thermistor/LCD Display shows opposite change in temperature
Not much can go wrong with the temperature sensor lookup code, What temperature sensor do you have, and what sensor number did you choose.
View ArticleRe: Flsun Delta Kossel W/ Marlin 1.1.6f-AC FW not leveling properly
Good evening. I hope you already got your printer working. IF you haven't I just went through a similar issue. My printer would crash into the bed and then print in the air. I have it working now. I...
View ArticleCBot Marlin to 'mainline' marlin 1.0 or 1.1
I just got a 3d printer by Createbot, a Prusa i3 clone, that I have their firmware for (albeit it was broken as sent to me and I had to fix it to get back to square one), and it works, but I'm...
View ArticleRe: Motors Off after 2 mins ?
Sorted ! I did a search for '120' (2 x 60 seconds) through the Marlin code and found DEFAULT_STEPPER_DEACTIVE_TIME 120 in configuration_adv which switches the motors off after a period of inactivity....
View ArticleRe: CBot Marlin to 'mainline' marlin 1.0 or 1.1
For sure... You want to move to Bugfix v1.1.x Use a visual diff program like Notepad++ (with the visual diff add on enabled) to help with the migration. It should only take 10 minutes to cross your...
View ArticleRe: CBot Marlin to 'mainline' marlin 1.0 or 1.1
I upgraded for 1.1.0 RC8 recently to Marlin 1.1.5 using the previous version of that controller without the SD card. Thought he firmware is Identical with the On board SD Card. I Can help you to make...
View ArticleRe: Thermistor selection Marlin 1.1.8
Can anyone lend a hand? I know zip about python. I have installed "IDLE" and cut/pasted the script from that link into a file but when I tell IDLE to check module via ALT-X I get a syntax error ?!?...
View ArticleRe: Thermistor selection Marlin 1.1.8
Tried Python 3.6.4 and got a different error. :( This error when I research it makes me think that I should be using Python 2 but that loops me back to the first issue with Python.....
View ArticleRe: Thermistor selection Marlin 1.1.8
Ok, started from scratch on a different PC and it worked. now I am lost at how to input the data I have been able to glean from Google into this script... 104NT-4R025H42G I for Steinhart Hart...
View ArticleRe: Thermistor/LCD Display shows opposite change in temperature
Well, I thank you for responding to the post, but upon re-uploading the code today the thermistor/LCD are now working as they should. While I'm glad the issue has somehow resolved itself, I'm hesitant...
View ArticleRe: Thermistor selection Marlin 1.1.8
DONT use a lighter... approx 1970C , will damage thermistor.
View ArticleRe: Thermistor selection Marlin 1.1.8
according to this page type 1 is close enough [reprapworld.com]
View ArticleRe: Thermistor selection Marlin 1.1.8
QuoteDust DONT use a lighter... approx 1970C , will damage thermistor. I was kidding :) dang it after all that work I was really hopeing to use that script :) But thanx I will try type 1
View ArticleRe: Thermistor/LCD Display shows opposite change in temperature
I have had problems with Marlin after being flashed. And need to do a M502 then save using a M500. The reason is because the Flashing process does not erase the save data. Reloading Firmware defaults...
View ArticleX offset between nozzle and start bed
Hello, i've a question about bed area (sorry for my english) when my head (with nozzle) make homing on X axies, it push the min_endpoint swith and marlin configure it's 0 x axies, it's normal. Marlin...
View ArticleRe: X offset between nozzle and start bed
Quoteyou think i need to configure this ? : #define X_MIN_POS 30 very close, but no you want. #define X_MIN_POS -30 So when it homes it thinks its at -30, then 0 is 0 on your bed.
View ArticleRe: X offset between nozzle and start bed
QuoteDust Quoteyou think i need to configure this ? : #define X_MIN_POS 30 very close, but no you want. #define X_MIN_POS -30 So when it homes it thinks its at -30, then 0 is 0 on your bed. Seems...
View Article