Re: 3D Printer RAMPS 1.4 SD Card Reader
QuoteRoxy You can buy a new RAMPS v1.4 board for under $4 (including shipping) on eBay: [www.ebay.com] If you are doing this because you enjoy it and just want to play with things, that is fine. I'm...
View ArticleRe: 1.1.7 after auto home / bed leveling raises Z 10mm:(
So I tried these. // #define Z_CLEARANCE_DEPLOY_PROBE 10 <<<< Won't verify / Must be defined #define Z_CLEARANCE_DEPLOY_PROBE 0 <<<< "0" appears to be invalid in per comments....
View ArticleRe: Mixed Bed leveling possible? (UBL and manual)
Thank you for this explanation. Not quite as comfortable as before but it is a workable solution for now.
View ArticleRe: 1.1.7 after auto home / bed leveling raises Z 10mm:(
I think this is a bug and I really think I should have the option of disabling this. I am considering moving on to 1.1.8 and see what happens.
View ArticleRe: 1.1.7 after auto home / bed leveling raises Z 10mm:(
The Z-Probes need some amount of clearance. Set it as low as you can without damaging your printer. But seriously... Even a 10 mm move is nothing in the big picture. Most of my prints are 6 or 10...
View ArticleThermistor selection
I have a SEMITEC 104NT-4-R025H42G screw in type thermistor on my hotend. I dont see that on the thermistor table to select so I used type 5 104GT-2 with Marlin 1.18 Googleing about a bit I am pretty...
View ArticleRe: 1.1.7 after auto home / bed leveling raises Z 10mm:(
It is not so much the 10mm's that is bothering me. It stems from the fact that I can't seem to get my bed dialed in now. Let me explain my leveling workflow before and after 1.1.7. Most of the time I...
View ArticleRe: 1.1.7 after auto home / bed leveling raises Z 10mm:(
Well...Its good to see that entire work flow. You are obviously very serious about having the printer setup right. One of the problems with that work flow is measuring the distance between the nozzle...
View ArticleRe: 1.1.7 after auto home / bed leveling raises Z 10mm:(
Thank you for that Roxy. I'm going to look at the setup on UBL. I'm using bi-linear at the moment. I'm being told that my as my printer (Tronxy 802MA) shipped the Z offset was set to -0.5 in the...
View ArticleFlsun Delta Kossel W/ Marlin 1.1.6f-AC FW not leveling properly
Hi everyone, this is my first post here. I'm helping a friend fix his Flsun Kossel Delta. We never could get it to work properly, and the fact that it shipped with the wrong firmware is probably why....
View ArticleUser Error? Endstops don't work
So I'm sorta at wits end here.. I'm definitely new to building a printer, so that could be it. Here's the situation: I have a chinese RAMPS v1.4 + arduino + LCD. I flashed it with a mostly...
View ArticleRe: Thermistor selection Marlin 1.1.8
8 bit machines to slow to do the maths real time.... thus they use tables you can generate your own table see [github.com]
View ArticleRe: Issue uploading Marling Firmware on RAMBo
Did you find an answer to this? I am there right now! Cheers Alex
View ArticleRe: Issue uploading Marling Firmware on RAMBo
I found that a fix posted in the Repetier forum also works in Marlin I was compiling Marlin 1.1.x on Arduino 1.8.2 for RAMBo 1.2d I got this error: 'DIGIPOT_MOTOR_CURRENT' was not declared in this...
View ArticleRe: User Error? Endstops don't work
What firmware are you using, what configuration 3D Printer do you have.
View ArticleRe: 1.1.7 after auto home / bed leveling raises Z 10mm:(
My suggestion would be to turn off all bed leveling. And get the Z_PROBE_OFFSET_FROM_EXTRUDER number correct so you can home in the center of the bed, and print a small object there. Perhaps a 20mm...
View ArticleRe: User Error? Endstops don't work
I'm using Marlin 1.1.7 with a normal Cartesian/i3 type setup. But I ended up solving my own issue.
View ArticleRe: User Error? Endstops don't work
It always feels great when you find your own solutions. Need any help just post!!!
View ArticleRe: Thermistor selection Marlin 1.1.8
ok, that looks like it will take some learning :)
View ArticleRe: Thermistor selection Marlin 1.1.8
If you generate (and add) a table... Try to be smart about the range of values and the spacing. Marlin does a sequential, linear search from the end of the table. So just a few values at the higher...
View Article