It is not so much the 10mm's that is bothering me. It stems from the fact that I can't seem to get my bed dialed in now. Let me explain my leveling workflow before and after 1.1.7. Most of the time I don't go through this procedure because once I have it dialed in I don't touch it. I usually only do this if I've had it apart or am having print problems.
Before 1.1.7:
(Short version)
Perform auto home from LCD control panel
Nozzle stays at set height
Insert business card and check drag
Adjust inductive sensor up or down if needed
Auto home again
Check drag with business card
If drag is good then print (if not repeat until drag is correct)
(Long version) usually reserved for if I've had the printer apart
Perform auto home from LCD control panel
Nozzle stays at set height
Insert business card and check drag
Adjust inductive sensor up or down if needed
Auto home again
Check drag with business card (repeat until correct)
Power down steppers
Manual 5 point check with card (center and all corners of bed)
Adjust bed with thumb screws
Auto home again
Check drag with business card (repeat until correct)
Print
After 1.1.7:
(Short version)
Perform auto home from LCD control panel
[[[[Nozzle raises 10mm
Drop nozzle 10mm from slicer control panel]]]]
Insert business card and check drag
Adjust inductive sensor up or down if needed
Auto home again
[[[[Nozzle raises 10mm
Drop nozzle 10mm from slicer control panel]]]]
Check drag with business card
If drag is good then print (if not repeat until drag is correct)
(Long version) usually reserved for if I've had the printer apart
Perform auto home from LCD control panel
[[[[Nozzle raises 10mm
Drop nozzle 10mm from slicer control panel]]]]
Insert business card and check drag
Adjust inductive sensor up or down if needed
Auto home again
[[[[Nozzle raises 10mm
Drop nozzle 10mm from slicer control panel]]]]
Check drag with business card (repeat until correct)
Power down steppers
Manual 5 point check with card (center and all corners of bed)
Adjust bed with thumb screws
Auto home again
[[[[Nozzle raises 10mm
Drop nozzle 10mm from slicer control panel]]]]
Check drag with business card (repeat until correct???)
[[[[Print..... errrr DRAG NOZZLE ACROSS BED
GO TO BED FRUSTRATED
TRY AGAIN NEXT DAY
GO TO BED FRUSTRATED
TRY AGAIN NEXT DAY
GO TO BED FRUSTRATED
Now maybe it's my workflow but it worked for me and I could do the long version in a couple of minutes. I haven't printed in 5 days now. I am so irritated.
Before 1.1.7:
(Short version)
Perform auto home from LCD control panel
Nozzle stays at set height
Insert business card and check drag
Adjust inductive sensor up or down if needed
Auto home again
Check drag with business card
If drag is good then print (if not repeat until drag is correct)
(Long version) usually reserved for if I've had the printer apart
Perform auto home from LCD control panel
Nozzle stays at set height
Insert business card and check drag
Adjust inductive sensor up or down if needed
Auto home again
Check drag with business card (repeat until correct)
Power down steppers
Manual 5 point check with card (center and all corners of bed)
Adjust bed with thumb screws
Auto home again
Check drag with business card (repeat until correct)
After 1.1.7:
(Short version)
Perform auto home from LCD control panel
[[[[Nozzle raises 10mm
Drop nozzle 10mm from slicer control panel]]]]
Insert business card and check drag
Adjust inductive sensor up or down if needed
Auto home again
[[[[Nozzle raises 10mm
Drop nozzle 10mm from slicer control panel]]]]
Check drag with business card
If drag is good then print (if not repeat until drag is correct)
(Long version) usually reserved for if I've had the printer apart
Perform auto home from LCD control panel
[[[[Nozzle raises 10mm
Drop nozzle 10mm from slicer control panel]]]]
Insert business card and check drag
Adjust inductive sensor up or down if needed
Auto home again
[[[[Nozzle raises 10mm
Drop nozzle 10mm from slicer control panel]]]]
Check drag with business card (repeat until correct)
Power down steppers
Manual 5 point check with card (center and all corners of bed)
Adjust bed with thumb screws
Auto home again
[[[[Nozzle raises 10mm
Drop nozzle 10mm from slicer control panel]]]]
Check drag with business card (repeat until correct???)
[[[[Print..... errrr DRAG NOZZLE ACROSS BED
GO TO BED FRUSTRATED
TRY AGAIN NEXT DAY
GO TO BED FRUSTRATED
TRY AGAIN NEXT DAY
GO TO BED FRUSTRATED
Now maybe it's my workflow but it worked for me and I could do the long version in a couple of minutes. I haven't printed in 5 days now. I am so irritated.