Quantcast
Browsing all 12089 articles
Browse latest View live

Re: Marlin bed dimensions

use a ruler... eg X_MIN_POS -45 so from the X min position to the 0 position is 45 mm. Measure what it should be to the PrintBite 0 and replace 45 with that value.. leave the -, it means to the left...

View Article


Re: Porous prints on larger prints

QuoteThe e of 99.68 seems to print ok on the small prints. If i do a test extrude at this setting I only get about 40 of 50 mm There is a guide to calibrate e-steps ( and stepper current too ). Both...

View Article


About configuring the Marlin for Delta machine (single nozzle for multiply...

Hello, Recently, I downloaded a new version of Marlin 1.1.x and tried to configure it for my delta machine. My machine is a Kossel mini. I always got a error message as the following. Arduino: 1.6.9...

View Article

Re: Porous prints on larger prints

Good to know on the U1 for the autotune. I used the display to set them when I ran it. I checked the extrusion amount and it needed some more steps. It is now 112. The test print at the slow x and y...

View Article

Re: New marlin customisation problems

I have noticed this too, though it has not effected any of my prints. It comes on after the E0 has heated for a few seconds them the print begins. Never much paid attention to it as the Prints come...

View Article


Custom command not queued

Hey everybody! I create 2 custom commands (M10 & M11) to control a door locking system. Everything works well and I can lock and unlock my door using a out pin. But the command never queued after...

View Article

Re: Enable the Z steppers at startup

I did this and it works well!! Thanks!

View Article

Re: New marlin customisation problems

Progress. Of a sort. I managed to get a useable print whilst printing from cura on USB. On average the dimensions were within 0.4 mil of the 20mm box. then without making any changes i tried to print...

View Article


Re: Custom command not queued

Put an M400 Gcode before your M10 or M11 The M400 will wait until all prev movements Gcodes ends.

View Article


Unknown CPU error when updating to Marlin 1.1.3 with MKS Base 1.5 controller

I spent this evening attempting to update to Marlin v 1.1.3 from the much older version of Marlin that came with my reprap prusa i3. I adjusted all the stock settings accordingly for my machine and...

View Article

Re: Porous prints on larger prints

You are on the wrong path, believing you can slow down the printer by changing the scale of the print! You better do that from PC with a printerhost like Pronterface or Repetier-host. I'm sure you can...

View Article

Re: Unknown CPU error when updating to Marlin 1.1.3 with MKS Base 1.5 controller

posting the error log would give us at lease a marginal chance of helping you....

View Article

Re: Unknown CPU error when updating to Marlin 1.1.3 with MKS Base 1.5 controller

#define MOTHERBOARD BOARD_MKS_13 should work... really need to see the error.... My only guess is perhaps your using a old boards.txt file that is not designed for newer Arduino ide.. In which case...

View Article


Re: Unknown CPU error when updating to Marlin 1.1.3 with MKS Base 1.5 controller

Ah, I didn't realize there was more information to be seen by copying the error message. All I saw was the basic error at first. It was a rookie mistake, I forgot to set the proper board type in...

View Article

Re: Porous prints on larger prints

I have it printing really well with: M203 x10 y10 z5 e99.68 It is slow but the surfaces are very smooth and no holes. Going to start tweaking from here... Thanks...

View Article


Re: Porous prints on larger prints

Can i ask what slicer program you use

View Article

Re: Porous prints on larger prints

Cura v15.04.3 I've attached an Excel spreadsheet with the settings. I'm getting really good results but really slow. This morning I tried moving the m203 x and y up to 12 but I was getting the...

View Article


Re: Porous prints on larger prints

looking at your spreadsheet i think your main problem is the print speed =100, far to fast I would reset the M203 x and y to 100 and in the cura settings set the print speed to about 45 i have...

View Article

Re: Porous prints on larger prints

I'll do that on the next print. I'll let you know how it goes... Thanks...

View Article

Re: Porous prints on larger prints

Check your extruder again. It must not slip at 12mm/s print speed... Does it have a tensioner screw you can adjust? Maybe it is clamping the filament way to hard. If the tension is to low, it would...

View Article
Browsing all 12089 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>