Cura v15.04.3
I've attached an Excel spreadsheet with the settings.
I'm getting really good results but really slow.
This morning I tried moving the m203 x and y up to 12 but I was getting the slipping on the extruder that was causing to porosity. I reduced the print speed to 85% of that which is approximately x10 and y10.
Using Repetier Host for printing. It seems to do a good job. Tried printing with Pronterface to see if something in Repetier was causing it and go the same slipping on the extruder as before on the higher setting for m203
I also know that it is not set right because when Repetier starts one of my prints it tells me that it should take about 2 hours. The current print started at 7:00am this morning and is just now finishing at 12:44pm. That is about 5 hours and 44 minutes. That is about 35% of what Repeitier is reporting.
Here are the setting as shown by m501 in Pronterface
Connecting...
start
Printer is now online.
echo:Marlin 1.1.0-RC8
echo: Last Updated: 2016-12-06 12:00 | Author: (none, default config)
Compiled: Jun 4 2017
echo: Free Memory: 4639 PlannerBufferBytes: 1136
echo:V27 stored settings retrieved (398 bytes)
echo:Steps per unit:
echo: M92 X80.00 Y80.00 Z400.00 E111.00
echo:Maximum feedrates (mm/s):
echo: M203 X10.02 Y10.02 Z5.00 E25.00
echo:Maximum Acceleration (mm/s2):
echo: M201 X3000 Y3000 Z100 E10000
echo:Accelerations: P=printing, R=retract and T=travel
echo: M204 P100.00 R200.00 T200.00
echo:Advanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (ms), X=maximum XY jerk (mm/s), Z=maximum Z jerk (mm/s), E=maximum E jerk (mm/s)
echo: M205 S0.00 T2000.00 B20000 X20.00 Y20.00 Z0.40 E5.00
echo:Home offset (mm)
echo: M206 X0.00 Y0.00 Z0.00
echo:Material heatup parameters:
echo: M145 S0 H180 B70 F255
M145 S1 H240 B110 F0
echo:PID settings:
echo: M301 P30.47 I1.86 D125.02
echo: M304 P435.90 I85.28 D557.02
echo:Filament settings: Disabled
echo: M200 D3.00
echo: M200 D0
Not sure where to look to get the times down and get solid prints.
Any ideas?
I've attached an Excel spreadsheet with the settings.
I'm getting really good results but really slow.
This morning I tried moving the m203 x and y up to 12 but I was getting the slipping on the extruder that was causing to porosity. I reduced the print speed to 85% of that which is approximately x10 and y10.
Using Repetier Host for printing. It seems to do a good job. Tried printing with Pronterface to see if something in Repetier was causing it and go the same slipping on the extruder as before on the higher setting for m203
I also know that it is not set right because when Repetier starts one of my prints it tells me that it should take about 2 hours. The current print started at 7:00am this morning and is just now finishing at 12:44pm. That is about 5 hours and 44 minutes. That is about 35% of what Repeitier is reporting.
Here are the setting as shown by m501 in Pronterface
Connecting...
start
Printer is now online.
echo:Marlin 1.1.0-RC8
echo: Last Updated: 2016-12-06 12:00 | Author: (none, default config)
Compiled: Jun 4 2017
echo: Free Memory: 4639 PlannerBufferBytes: 1136
echo:V27 stored settings retrieved (398 bytes)
echo:Steps per unit:
echo: M92 X80.00 Y80.00 Z400.00 E111.00
echo:Maximum feedrates (mm/s):
echo: M203 X10.02 Y10.02 Z5.00 E25.00
echo:Maximum Acceleration (mm/s2):
echo: M201 X3000 Y3000 Z100 E10000
echo:Accelerations: P=printing, R=retract and T=travel
echo: M204 P100.00 R200.00 T200.00
echo:Advanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (ms), X=maximum XY jerk (mm/s), Z=maximum Z jerk (mm/s), E=maximum E jerk (mm/s)
echo: M205 S0.00 T2000.00 B20000 X20.00 Y20.00 Z0.40 E5.00
echo:Home offset (mm)
echo: M206 X0.00 Y0.00 Z0.00
echo:Material heatup parameters:
echo: M145 S0 H180 B70 F255
M145 S1 H240 B110 F0
echo:PID settings:
echo: M301 P30.47 I1.86 D125.02
echo: M304 P435.90 I85.28 D557.02
echo:Filament settings: Disabled
echo: M200 D3.00
echo: M200 D0
Not sure where to look to get the times down and get solid prints.
Any ideas?