Quantcast
Channel: Reprap Forum - Firmware - Marlin
Browsing all 12090 articles
Browse latest View live
↧

Bed levelling in 1.1.0 rc3

Is there anything different in how this version applies bed correction after g29? I notice it generates and outputs a bed compensation matrix. Is it adjusting the bed by applying a plane to the z...

View Article


Re: full smart graphic controller encoder problem

The issue I have with the same setup is the encoder works in reverse ie increase value is anticlockwise and decrease is clockwise, this feels counter-intuitive.

View Article


Re: ulticontroller rev2.1 in Marlin 1.1.0-RC3

No progress. I guess it would require porting some code to Marlin last version...

View Article

Re: Dual extruder with different step/mm

QuoteThe + 3 to increase the value of active extruder of the three previous axis. I DONT KNOW EXACTLY WHAT IS THIS MEAN? To me it looks like the extruders are numbered 1-2, but the actual "axis" port...

View Article

Re: Bed levelling in 1.1.0 rc3

Well I've answered this myself by experimentation, if I trigger the sensor at one point before the bed gets to it then print a bed level test the entire bed level is affected not just the level in...

View Article


Re: G28 misbehaving/behaving

I guess just like waiting for the first service pack before upgrading Windows I think i'll wait for 1.1 to be out of RC. Having to issue G28 twice is at the end of the day just a quirk. Thanks Thinkyhead

View Article

Re: G28 misbehaving/behaving SOLVED

Just closing this up

View Article

Re: full smart graphic controller encoder problem

Hey DjDemonD, I have exactly the same reversed encoder issue. Bugged the hell out of me 12 months ago. I solved the problem by stopping using it.

View Article


Re: full smart graphic controller encoder problem

It is easy enough to change the direction. This might already be solved for you: [github.com] (Look for the Blue-Marlin post at the end of the thread)

View Article


Re: Bed levelling in 1.1.0 rc3

QuoteDjDemonD Well I've answered this myself by experimentation, if I trigger the sensor at one point before the bed gets to it then print a bed level test the entire bed level is affected not just...

View Article

Re: Bed levelling in 1.1.0 rc3

Having just read this mesh bed levelling it seems as if this is exactly what I'm seeking however why it can't be done by auto probing when others have already done the work I do not understand....

View Article

Re: full smart graphic controller encoder problem

Okay so set encoder pulses per step to -1 I'll try this and see if it works, thanks.

View Article

Auto Bed Leveling causes Rod to pop out

Hi Guys, Last time I messed with this, it would get five minutes through the initial stages and then a rod would pop out because it would go out too far. It would still mange to continue for some...

View Article


Re: Bed levelling in 1.1.0 rc3

QuoteDjDemonD Having just read this mesh bed levelling it seems as if this is exactly what I'm seeking however why it can't be done by auto probing when others have already done the work I do not...

View Article

Re: Auto Bed Leveling causes Rod to pop out

Soon there will be better Delta Auto Bed Leveling code. But it will be another 5 or 6 weeks until it is ready.

View Article


Re: Auto Bed Leveling causes Rod to pop out

QuoteRoxy Soon there will be better Delta Auto Bed Leveling code. But it will be another 5 or 6 weeks until it is ready. good to know, thanks for this, but is there a setting I should know about to...

View Article

Re: Auto Bed Leveling causes Rod to pop out

Quotepringleman but is there a setting I should know about to change the width of the platform. For Delta Printers you control this with DELTA_PRINTABLE_RADIUS and DELTA_PROBEABLE_RADIUS. For...

View Article


Image may be NSFW.
Clik here to view.

Help me with FW e SW Delta printer

Hello everyone I'm doing a Delta Robot, like the one in the picture (link), for use as a 3D printer. The robot is driven by brushless motors 3 Nema 23 with its driver. This driver has the direction...

View Article

Re: Help me with FW e SW Delta printer

Usually the double rods are attached to a Carriage that moves up and down on a tower. I'm not sure this is really a Delta printer. It would seem the math all changes with these mechanics.

View Article

Re: MKs base v1.4 no option in marlin for EEFB

Ok, I have the latest very of Marlin and have the MKs board running EEFB but now for a totally new issue. After setting up the board I now no longer have lcd display. I have it setup correctly in...

View Article
Browsing all 12090 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>