X and Y axis skips forward before auto bed leveling.?!
I recently upgraded my lead screws and one motor to a Nema 23. Before the upgrade I had things pretty dialed in. And after the upgrade I only remember changing some speed settings and steps per mm....
View ArticleRe: X and Y axis skips forward before auto bed leveling.?!
Just in case anyone knows of anything to check.
View ArticleRe: Bed Leveling RC8
I have RC8 ABL working with a proximity sensor as my Z Min and probe. I home it (G28) and then G29 will perform the bilinear probing. If you want to see my config, please ask.
View ArticleLooking for some help understand a ZMIN ENDSTOP issue.
Hello, I have a almost finished Hypercube (corexy) printer. Ramps 1.4, Mega2560 with Marlin 1.1.0-RC8. I have a proximity sensor mounted near the hotend. I don't actually have a hot end installed yet,...
View ArticleRe: Looking for some help understand a ZMIN ENDSTOP issue.
It is common for RC-7 and RC-8 to do two independent raises of the nozzle after power up. The first one probably is to get clearance to home for the X and Y portion of the G28. The second raise can...
View Article[SOLVED] Looking for some help understand a ZMIN ENDSTOP issue.
I found that in Repetier Host, when defining the new printer, I had and old startup script from an old older printer. That script set the steps/mm which were quite different from this printer. So...
View ArticleFull graphics display wont work
Hello i have some very wird issus. First i have a Creality 3D Afinibot A9 printer, it is a very fine one, and it fit my need. i have now startet to add some extensions on it. the first thing is that i...
View ArticleRe: Full graphics display wont work
Have you enabled it in the firmware before up loading the firmware? I think you need to remove the # on the opproate line to enable it.
View ArticleRe: Full graphics display wont work
QuoteGRAYWOLF Have you enabled it in the firmware before up loading the firmware? I think you need to remove the # on the opproate line to enable it. i dont think that you know what you are talking...
View ArticleRe: Full graphics display wont work
Greywolf seems very confused... If they start with //#define they are disabled if they start with #define they are enabled define on its own will just stop it compiling.
View ArticleRe: X and Y axis skips forward before auto bed leveling.?!
Go through the logs on RH, and look at the move commands. Try them manually. Check you start script in RH, or slicr/cura, may be you have something there.
View ArticleRe: Full graphics display wont work
Greywolf was sorta on the right track ATM you have the standard 20x4 alpha numeric display enabled in the config.h file as Quote// The RepRapDiscount Smart Controller (white PCB) // [reprap.org]...
View ArticleRe: Marlin 1.1 RC8 reboots after bed reaches temps
I reflashed RC8 and the rebooting is gone but the problem for the rebooting still exist but manifests itself differently. I now get an error message , at the same 'spot', instead of rebooting. The...
View ArticleFull Graphics display on Megatronics v3.1
Greetings, I have a new Megatronics v3.1 with a Graphics Display LCD with controller and SD card reader. The board is working fine as is the LCD as I've put both through the their respective test...
View ArticleRe: Full Graphics display on Megatronics v3.1
What firmware are you using? ie something they provided, or latest from the internet To me it looks like the board type you selected simply doesn't have the lcd pins defined is the relevant pins.h eg...
View ArticleRe: Full Graphics display on Megatronics v3.1
Yeah, I had to use a more up to date firmware (the one on the page for the LCD itself), the one I was using was released before this LCD controller. The issue seems to be resolved now as far as the...
View ArticleBed Levelling on RC8 working but not compensating
Hi, I am trying to set up bed levelling with RC8, I have a Z Probe on the Z Min stop. Everything works fine, Homing to Z fine, G29 fine, G29 reporting looks fine, but when I actually try a print then...
View ArticleRe: Bed Levelling on RC8 working but not compensating
Modify your G-code and introduce G29 after G92 E0 command. In my case this works.
View ArticleRe: Bed Levelling on RC8 working but not compensating
Thanks but tried that and no joy. I did discover that the slicer was putting in an extra G92 E0 so I exported the GCode and edited it so G29 was after that but stil does the same thing. Here's the...
View ArticleRe: Bed Levelling on RC8 working but not compensating
And for completeness the debug output following G29 <-Bed Level Correction Matrix: <-+0.999954 +0.000000 -0.009590 <-+0.000018 +0.999998 +0.001875 <-+0.009590 -0.001875 +0.999952 <-...
View Article