Completion percentage on full graphic lcd
Hi, Is there an option in Marlin to show the completion percentage on the full graphic lcd? It shows a progress bar only which is less predictable. Thanks
View ArticleRe: Bed Levelling on RC8 working but not compensating
Pff.......i really don't know what to say.....I'm really sorry. In my case it compensate but it's not compensate enogh. I mean I see Z axes how rotates and try to compensate but they don t rotate...
View ArticleBitte um Hilfe! Fehler beim kompilieren Marlin RC8
Schönen guten tag ich hänge jetzt seit tagen beim kompilieren fest und verstehe einfach nicht was der fehler sein soll da ich nicht genau weis was ihr noch an infos braucht fragt bitte einfach ich...
View ArticleAdjusting Marlin for quite printing
Hi guys My printer make some disturbing noises when prints the contour of the object and the first layer. Something goes into resonance and start vibrate. This happend at any speed but at lower speeds...
View ArticleProblems with autolevel
My autoleveling seems a bit off and can't get it to function correctly. I tried raising the matrix to 5x5 but same result. After a G29 if I go to X200 Y200 Z0 I have a .2 gap between nozle and bed. If...
View ArticleRe: Adjusting Marlin for quite printing
Any ideas guys? I don't want to use towels or others things like this.
View ArticleRe: Adjusting Marlin for quite printing
Depends what drivers you are using What micro stepping What motors
View ArticleRe: Adjusting Marlin for quite printing
motors: Bipolar Nema 17 40N/cm 1.7A Motherboard: MiniRambo with drivers: 4982ET 16 microsteps. I have set them to 600mV/ driver witch I know is a decent value.
View ArticleRe: Adjusting Marlin for quite printing
Was going to suggest 1/32 micro stepping, but not possible with that MB driver combo. Have you tried repetier firmware, i read somewhere it tends to run quiter than marlin, I have not compared them tho.
View ArticleRe: Adjusting Marlin for quite printing
Nop,i didn't try it. But I think to stay on Malrin as I have experience with it. MB can do 1/32 microstepping but as i increase the number of microsteps the motors gets weaker and I can't do prints at...
View ArticleRe: Bed Levelling on RC8 working but not compensating
Pain Over, loos like I discovered the issue, I moved G29 further down the start G code and its now working. the only remaining issue is that I have a weird setting for the z Probe offset, when...
View ArticleRe: Bed Levelling on RC8 working but not compensating
I don't know... For me, setting my Z offset with G92 Z10 after G1 Z0 for example is not working and I'm using repetier. I mean on my LCD shows that Z is 10 but in my repetier on Z axis is still...
View ArticleRe: Bed Levelling on RC8 working but not compensating
All of the parameters are loaded from the EEPROM. You need to do a M502 followed by a M500 to get the new values to stick. Or if you do a M851, follow it up with a M500 to save the value.
View ArticleRe: Bed Levelling on RC8 working but not compensating
Hi, thought it was all solved, It seems to all be working fine, and I see the Z motors turn as the head moves though the print so its adjusting the Z Height, but it doesn't seem to be adjusting...
View ArticleRe: Bed Levelling on RC8 working but not compensating
Hah......you tell me bro. I'm thinking about this for 2 weeks now on. I have the same problem...I still didn't found the solution. I think the autobed leveling procedure is good but for very small...
View ArticlePossible to set "ZMin" when doing bed leveling / Z probing
Question: Can a "ZMin-while-probing" be set? Meaning a minimum Z height the printer bed can move to, while Z Probing. Purpose: For safety reasons should the probe switch not fire for some reason. --...
View ArticleRe: Bed Levelling on RC8 working but not compensating
I might have to go back to using the software print levelling option until thi is properly sorted.
View ArticleRe: Possible to set "ZMin" when doing bed leveling / Z probing
IIRC it is called" software_endstops" and prevents the head from going out of borders.
View ArticleG code for calibration
This is my code for adjusting my bed. But after cleaning nozzle process my printer suddenly set extruder temp to 0. Why is that? What is wrong? G21 ;metric values G90 ;absolute positioning M82 ;set...
View Article