Re: Auto Bed Leveling Setup issues - I don't understand :-(
I have the front left as 0,0 on my i3
View ArticleZ probe repeatability - no data
I enabled z probe repeatability in the firmware, but when I run a M48 command, I get all 0s: SENDING:M48 n10 V4 M48 Z-Probe Repeatability Test Positioning the probe... echo:busy: processing echo:busy:...
View ArticleRe: Z probe repeatability - no data
If those numbers were correct, you would have a perfect printer. But obviously, you have something else going on. Does it home with a G28 correctly? Do you have an LCD Display panel? What does it say...
View ArticleRe: Z probe repeatability - no data
Yes, it homes correctly. I do have a LCD panel. After I home with a G28 or with the home xyz button on pronterface, it homes and then goes to X100, Y140, Z0. That's what the LCD says, and an M114 says...
View ArticleRe: Z probe repeatability - no data
And a couple more questions: Are you using a Cartesian or a Delta printer? The M48 was not supported on Delta's until 6 or 9 months ago. Are you using marlin's RC-7 or RC-8 ? If not... You should...
View ArticleRe: Z probe repeatability - no data
I'm using RC8 on a cartesian prusa mendel 3. I have mesh leveling enabled. I haven't tried that exact command Obewan, but I have tried probing different points with M48 and V4. Not home right now, but...
View ArticleRe: Auto Bed Leveling Setup issues - I don't understand :-(
Thanks for your help guys! I finally got the printing working and homing where I want it to! :) Now that it's printing, having one final issue with the prints. I am using a MakerGeeks Translucent...
View ArticleRe: Auto Bed Leveling Setup issues - I don't understand :-(
With a .4 nozzle you should be printing more like .2mm layers for better quality. Also 230c is really hot for most PLA. Thats ABS temps. Try 200-210 and see if it improves. Do you also have a part...
View ArticleRe: Auto Bed Leveling Setup issues - I don't understand :-(
Hi Floyd! Thanks for your response! I will try the .2 layer height as you suggested and see what happens. The 230C I actually got from the paperwork (attached is a copy). From what I have read...
View ArticleMin Temp not lower than 76ÂșC
Hi, This problem does not really affect my prints, but my curiosity would come down if I understand why this is happening. I am currently using a P3Steel printer running with Arduino Mega, RAMPS 1.4...
View ArticleMarlin Diamond Hotend
Hey! I have a Prusa i3 Hephestos and I will install the Diamond Hotend soon. I have a question regarding the firmware. At reprep.me they recommend "Marlin - The Diamond Hotend version" [github.com] I...
View ArticleRe: Marlin Diamond Hotend
If the Diamond Hotend version is on GitHub, it should be straight forward to see what they changed from the normal Marlin. And depending how much they changed, it shouldn't be too bad to cross those...
View ArticleRe: Auto Bed Leveling Setup issues - I don't understand :-(
If you have the PLA temperature too hot, the plastic will be too soft. You will especially notice the effects at the corners because the plastic stretches when it is hot. As it cools, it starts...
View ArticleRe: Auto Bed Leveling Setup issues - I don't understand :-(
Hi Again Roxy Ok... I will knock the temp down tomorrow and see what kind of results I get from that! For You and Floyd Both... Thanks for the advice! Don W.
View ArticleRe: Auto Bed Leveling Setup issues - I don't understand :-(
Lets see some testing results! Also .4mm layers with a .4mm nozzle is insane! General rule of thumb is never go more than 80% the nozzle diameter for layer height. With my .4mm nozzle .3mm is my fast...
View ArticleRe: Auto Bed Leveling Setup issues - I don't understand :-(
Hi Guys... Got just got back from a "medical thing" that left me incapacitated for a day. Still not 100% nut at least I can sit upright for a while! :-) Attached are pictures of my "Spocktipus"...
View ArticleAnyone know if a RUMBA, CoreXY and Marlin RC-8?
Anyone know if this combination will work together? thank you
View ArticleRe: Auto Bed Leveling Setup issues - I don't understand :-(
You possibly have a G28 X0 Y0 in your slicers end gcode you could add a G1 Y200
View ArticleRe: X axis does not raise between auto leveling points
Hi dark_man did get the problem solved because I have exactly the same and I m getting mad!!!! Would be amazing if you could share your experience.
View Article