Re: Marlin RC8 AUTO BED LEVELING BILINEAR
QuoteScott1326 Quotegavatron3000 Hey mate I've had similar issues with this as well, I've found it hard to setup and the gcodes don't seem to respond correctly either, I abandoned the auto bilinear...
View ArticleRe: Marlin RC8 AUTO BED LEVELING BILINEAR
QuoteScott1326 Hello Roxy, I have tried Marlin UBL, and as a matter of fact, you've replied to some of my questions on github (you may recall that the xy probe positions were off on my setup). I still...
View ArticleRe: Any Experience for SD Card Logging
I think we could be a little more elegant about it. Ignoring the SD-Memory card case, we could have the host computer keep track of how far it got. And it could do some clever things to recover and...
View ArticleRe: Any Experience for SD Card Logging
also MKS TFT28 LCD already has a controller (the smart LCD) that has battery backup eg banggood
View ArticleRe: Any Experience for SD Card Logging
Well... Here is something to keep in mind: The AVR processors do not clear memory when they reset. If the user did not cycle power, it would be possible to have a small piece of memory set aside to...
View ArticleInductive probe doesn't recognized as the Z endstop
Hello all, I use a Prusa i3 with a Ramps 1.4 and an inductive probe on Z axis. I recently update the old version of Marlin firmware for Marlin 1.1.0 RC8. I have one problem with this new version: the...
View ArticleRe: Inductive probe doesn't recognized as the Z endstop
what type of probe NPN or PNP, 5v or 12v? normally closed or normally open? (the fact that it doesn’t change means at this stage don’t worry about normally open or normally closed) How is it wired?...
View ArticleRe: Inductive probe doesn't recognized as the Z endstop
Thank you for your anwser. I will try to enable the fine endstop settings. According to the inductive probe, the features are the following: NPN DC6-36V 300mA Normaly open I used an electronic adapter...
View ArticleAuto Bed Leveling Setup issues - I don't understand :-(
Hi Guys (and girls) Ok. I have an ANET A8 chinese knockoff and after a number of THEIR driver boards being bad, I replaced it with a standard R.A.M.P.S setup and I FINALLY got it printer "printing",...
View ArticleRe: Auto Bed Leveling Setup issues - I don't understand :-(
You have not properly accounted for your probe offsets. For example, you say the probe is offset 56mm in the Y direction. But you are saying you want the front bed probe position to be 50. That...
View ArticleRe: Auto Bed Leveling Setup issues - I don't understand :-(
Hi Roxy Maybe this is where I'M getting confused? On my printer, The 0 position for the bed (the Y axis) is all the way back where the edge of the bed is over the stepper. The "Front" is where the...
View ArticleRe: Auto Bed Leveling Setup issues - I don't understand :-(
I don't like the "Front" and "Back" labels just because of situations like this. But historically... The origin of the printer is normally in the front left of the bed. If your origin is in the back...
View ArticleRe: Auto Bed Leveling Setup issues - I don't understand :-(
Hi Roxy! Thanks SO much for your help! I still don't understand the math behind how it arrives at the points to check, but your information cleared a LOT up in my mind as to how things are adjusted! I...
View ArticleRe: Auto Bed Leveling Setup issues - I don't understand :-(
Quoteimwhoim54 Hi Roxy! Thanks SO much for your help! I still don't understand the math behind how it arrives at the points to check, but your information cleared a LOT up in my mind as to how things...
View ArticleRe: Auto Bed Leveling Setup issues - I don't understand :-(
Quote#define Y_PROBE_OFFSET_FROM_EXTRUDER 56 // Y offset: -front +behind [the nozzle] Is this not expecting the Y0 position to be at the front of the bed, the way you have your Y home set, this should...
View ArticleRe: Auto Bed Leveling Setup issues - I don't understand :-(
Thanks again Roxy and Thanks obewan... The one thing that alludes me is how to set the x-y home position print printing is complete. Right now it's square in the middle of the bed Which is fine for...
View ArticleRe: Auto Bed Leveling Setup issues - I don't understand :-(
Roxy, How would you feel about putting up a YouTube video of the UBL mesh setup and use?
View ArticleRe: Auto Bed Leveling Setup issues - I don't understand :-(
After taking another look at your picture, Is your Y end stop located at the back(as you call it) of the printer, ie oposit end to the dsplay, if it is then that would be a Y min endstop and homing Y...
View ArticleRe: Auto Bed Leveling Setup issues - I don't understand :-(
Hi Obewan You are absolutely correct. The "rear" of my bed when facing the front of the printer is where 0,0 is located. That was my initial stumbling block. One I set the "Front" of the printer at...
View ArticleRe: Auto Bed Leveling Setup issues - I don't understand :-(
Quoteimwhoim54 Since it's my frist printer, not sure which corner is "supposed" to be home... can anyone enlighten me? Any corner is fine. But most people have the front left as (X,Y) = (0,0)
View Article