Marlin bugfix-2.0.x and REARM - MAX6675 Problem
Hello all ... I´m new in this forum. I have problems to get MAX6675 to work on the following configuration: latest Marlin bugfix-2.0.x FW on REARM board with Ramps 1.6 addon ......
View ArticleRe: Marlin bugfix-2.0.x and REARM - MAX6675 Problem
Same problem with Marlin 2.0.5 with Max6675 connected to P0_15 and P0_17 for SCK and SO :-(
View ArticleMarlin 2.x on ReARM - filament width sensor question
Hello all, i tried to set up the filament width sensor function to test it before using it with the following setup: REARM board with Ramps 1.6 addon ... REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER...
View ArticleTrouble setting up Marilin4Due: MINTEMP triggered, system stopped! Heater_ID
So I'm building a printer by myself and I'm stuck in setting it up. I use: - Arduino Due, RADDS, RAPS128, Hexagon Hotend with 100k EPCOS thermistor ( I don't have other thermistors) - Arduino IDE,...
View ArticleRe: Trouble setting up Marilin4Due: MINTEMP triggered, system stopped! Heater_ID
"Marlin 1.0.3 dev" This is a dinosaur Real marlin has supported due for ages. Please consider Marlin 2. But the most obvious thing is you have the thirmistor plugged into the wrong place. (or pins...
View ArticleRe: Integrating a Custom 32 Bit Board in Marlin 2.0
@JMS728 I had a similar Problem, in the Pins-File you have to define Pins for X-/Y-/Z-axis and E0 to Ex for the rest of the Stepper-Drivers. If you then enable "X_DUAL_STEPPER_DRIVERS" in...
View ArticleRe: Update Marlin 1.1.8 to 2.x LCD&SD problem
Dear, first of all, thanks a lot for your suggestion. The change works fine to remove the artifacts, and the LCD shows the infos correctly. The problem of SD card reading remains, I have tried to...
View ArticleRe: MKS SGen L V1.0
Could you please go into detail how you managed to get MKS SGEN L + MKS TMC2209 v1 to work with sensorless homing? I tried setting everything correctly in Marlin and connected the "middle" pin (the...
View ArticleRe: MKS SGen L V1.0
If you connected diag0 to the endstop pin and you still show triggered you might need to invert the endstop logic. I am at work and don't have my config files but I believe that is all that is needed...
View ArticleRe: MKS SGen L V1.0
I too would appreciate a copy of your configuration.h and any other configuration file so I can see the changes that were altered to get sensor-less to work, thanks.
View ArticleRe: MKS SGen L V1.0
Off the top of my head... Assuming the jumpers on the board are correct you should need to set tmc2209 as the driver type for your axis. Set your machine movement/speeds, enable sensorless homing for...
View ArticleRe: MKS SGen L V1.0
Thanks for your fast response :) I removed the jumpers under the drivers, and testing via pronterface says communication to drivers is ok. [learn.watterott.com] Can you please confirm that this is the...
View ArticleRe: MKS SGen L V1.0
For the mks tmc2209 the diag0 port is the "top of the triangle". The link you posted is correct as far as the diag0 location. Connect that diag0 to your endstop signal pin when you are ready to...
View ArticleScara 3d printer
Hello everyone :) I am building a scara 3d printer and the trouble with the firmware drove me up the wall. I read before that marlin 1.x is broken for scara, when marlin 2.0 was out i tried it and the...
View ArticleRe: MKS SGen L V1.0
I connected both of them (X and Y) according to your instructions now. Now they are shown correctly as open when I check with M119. They wont be triggered when hitting the casing though. I tried...
View ArticleRe: MKS SGen L V1.0
Yes, quick home is more problems than it is worth with sensorless homing. Glad you are on the right path. As I noted before, find the threshold where your axis instantly triggers home and then drop...
View ArticleMarlin 2.0 newbie questions
Hi, I am trying again to get marlin set up on an SKR board. I have both an SKR V1.3 and a Mini DIP V1.0. I had tried in the past but could never get the firmware onto the board. I did get a successful...
View ArticleRe: Marlin 2.0 newbie questions
A somewhat pointless question if you can't even upload to the board.... I would recommend bugfix as that is where all the fixes go first.
View ArticleRe: Marlin 2.0 newbie questions
Some hints The sd card that comes with these board is complete garbage, do not use them. The two boards SKR V1.3 and the Mini DIP V1.0. are very different processors and the upload procedure is...
View ArticleRe: Marlin 2.0 newbie questions
QuoteDust Some hints The sd card that comes with these board is complete garbage, do not use them. The two boards SKR V1.3 and the Mini DIP V1.0. are very different processors and the upload procedure...
View Article