Re: Marlin 2.0 newbie questions
So I got marlin to compile finally. I tried to use the old config file with the newly downloaded marlin 2.0.X bugfix and it wouldn't work. I ended up having to completely delete the entire folder and...
View Articlestrange behaviour after changing to marlin 2.0.5.1
hello. I am at a loss to know how to proceed with the following that came about after upgrading to 2.0.5.1. 1. No start signal detected- forcing start-- this comes up every time I connect the printer,...
View ArticleRe: strange behaviour after changing to marlin 2.0.5.1
This sounds like you may need to restore the Firmware defaults and save them. This can be done from the LCD using RESTORE FAILSAFE and STORE MEMORY or sending M502 - Factory Reset and M500 - Save...
View ArticleRe: Marlin bugfix-2.0.x and REARM - MAX6675 Problem
The MAX6675 chips are not the problem, i have tested them with an arduino nano. They work fine also on 3.3V. Does no one have any idea how to fix this problem? And does nobody have a MAX6647 running...
View ArticleRe: Marlin bugfix-2.0.x and REARM - MAX6675 Problem
There is a setting to ignore temp reading for a while till they settle after boot, and I suspect you need this. But I cant remember the keyword (and it is most frustrating)
View ArticleRe: Marlin bugfix-2.0.x and REARM - MAX6675 Problem
Found it set #define BOGUS_TEMPERATURE_GRACE_PERIOD 2000 in your Configuration.h
View ArticleRe: Marlin bugfix-2.0.x and REARM - MAX6675 Problem
@Dust Thanks for your tip, unfortunately the setting causes a delay of the problem by about two seconds (max. temp. error)
View ArticleRe: strange behaviour after changing to marlin 2.0.5.1
Thanks for your input, I will try that ASAP. One thing I forgot to mention in my original post was that when I did the config file I commented out the eeprom with the intention of getting the printer...
View ArticleRe: strange behaviour after changing to marlin 2.0.5.1
I do not believe will M502/M500 work without EEProm enabled.
View ArticleRe: strange behaviour after changing to marlin 2.0.5.1
Thanks for that, I will redo the config tomorrow and try again
View Articlewrong sensorless homing with TMC2130 driver on Anet A8
Hi everyone, Due to a failure of the motherboard of my Anet A8, I decided to upgrade it by installing the following kit : - Arduino 2560 R3 - RAMPS 1.6 PLUS - TMC2130 drivers on X,Y,Z and E -...
View ArticleUpgraded from Marlin 1.02 to 2.03 & 2.04 now Homing randomly failing Failes
[attachment 114926 Configuration.h] - Pegasus 8 LCD -(Basic) [attachment 114927 Configuration.h] - Pegasus 8 LCD [attachment 114928 Configuration.h] - Pegasus 12 LCD I have (3) Maker farm Pegasus...
View ArticleMarlin dev-2.1.x with (lots of) TMC2130 shows 'TMC connection error'
Hello all, I am having some trouble with my RAMPS 1.4 + RAMPSXB +self designed board. I am trying to run all 9 drivers with TMCs. Chip select signals for them were provided by 2 PFC8574 and a modified...
View ArticleRe: Marlin bugfix-2.0.x Additional Preheat settings
Thank You AJMartel... I had added Preheat settings in Config.h for HDPE, TPU and PETG, but they weren't showing up when I flashed to my Ender 5... I assume these additional changes to Language_en.h...
View ArticleRe: Marlin bugfix-2.0.x Additional Preheat settings
The following link should open to show you all the changes required to add more than 2 preheat settings: [github.com] Good luck!
View ArticleRe: 5 x Tool changer Marlin E3D style
Sorry for the slow reply. I have built the tool changer mechanism and fitted it to my printer and am now figuring out if I can get marlin 2.0 running in a tool changer configuration on the...
View ArticleRe: 5 x Tool changer Marlin E3D style
This video is from a few weeks ago, I have installed better Springs and cleaned up the 3D printed part to ring contact point, slides in nicely now and stays locked better. [youtu.be]
View ArticleZ auto-align question
Trying to set up Z auto-align for the first time on a 320x320mm bed with a usable 300x300mm area. Could someone interpret what the positions are on the following statements? Thanks. #define...
View ArticleRe: Ender 5 slams into X and Y endstops! Firmware?
How comfortable are you with Arduino or Raspberry Pi, or using a TINYUSP board?? In order to upload new firmware to a stock Ender, you'll need to either use a USP to flash the firmware directly, or...
View ArticleRe: Error when compiling Marlin 2.0
MarlinConfig.h should be in the Marlin>src>inc folder along with a few other files... (see image of my src folder)... clearly VisualStudio it can't find it! :-( Suggest re-download Marlin...
View Article