Re: 230K Thermistor
Quote762x51 I like the Smoothie Smoothie likes you too then :) Quote762x51 but I also like that the Rumba's stepper drivers can be changed out if one of them decides to let the smoke out and stops...
View ArticleRe: Marlin RC6 with graphic LCD causes short pauses while printing
Both Deltas and the Full Graphics controller use a lot of processing power. Going to a 4x20 LCD would help a lot until Full Graphics LCD code gets a re-write to speed it up.
View ArticleRe: Marlin RC6 with graphic LCD causes short pauses while printing
Thanks for confirmation. Now i went back to 4x20 LCD and things are normal again. I wasnt' bothered too much about those pauses, but at spots when those pauses occured i've got excess of plastic so...
View ArticleRe: Marlin RC6 Not Booting/Communicating
I did 2 things. 1. I flashed the HID bootloader (included in package below, you need to use the icsp header on the Printrboard and an ISP programmer (I used an Arduino Mega 2560 I had from a RAMPS...
View ArticleRe: Marlin RC6 Not Booting/Communicating
I tried Marlin RC1 through RC6 and RC1 was the only one that worked. I ended up with the current stable release 1.0.2-1 but it kept giving me serial disconnects. Flashed back to my original version.
View Articleeasy way to upgrade from v1 to RC6
I have my hellos Marlin v1 original came with my i4 Prusa and I want insteller Marlin RC6 for my bltouch probe , is there a simple way to do this without losing the basic adjustment ? sorry for my...
View ArticleRe: easy way to upgrade from v1 to RC6
Quotenikos1234 I have my hellos Marlin v1 original came with my i4 Prusa and I want insteller Marlin RC6 for my bltouch probe , is there a simple way to do this without losing the basic adjustment ?...
View ArticleRe: easy way to upgrade from v1 to RC6
I try to do but I have an error message for offset
View ArticleRe: easy way to upgrade from v1 to RC6
/** * Marlin 3D Printer Firmware * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm...
View ArticleRe: easy way to upgrade from v1 to RC6
I'd use a file comparison tool to compare the configuration.h from your current setup with a clean version from Marlin v1 to see what changes were made I'd take note of those and just start with a...
View ArticleDEFAULT_AXIS_STEPS_PER_UNIT Above 999 - T8x2 Leadscrew
Hello, I need help setting up a new Marlin firmware. I have built a 3D printer (prusa) 18x18x18 custom made... I am using lead screws for all axis (XYZ)...They are not the 4 start 8mm (8mm per turn)...
View ArticleRe: DEFAULT_AXIS_STEPS_PER_UNIT Above 999 - T8x2 Leadscrew
It would make no sense to limit steps to 999 as an integer can go to 32000. The LCD however has limited space so they may limit the numbers shown to 3 digits. Did you test movement at the 1600 steps,...
View ArticleRe: DEFAULT_AXIS_STEPS_PER_UNIT Above 999 - T8x2 Leadscrew
Thanks for the reply. When I set at 1600 it only shows 600 and behaves as if it was set to 600 as well. I got those leadscrews T8x2 because I wanted to print slow but very accurate large prints (time...
View Articleplease help just another new strugling
Hi all i am relitivly new to all this and am hoping that someone can help me with the issues i have. i have had a look through the previously opened issues and i can't find any thing that is a direct...
View ArticleRe: please help just another new strugling
If you use source code files off a MAC on a Windows machine you need to remove the extra MAC files. The Window's Arduino IDE tries to compile those. For the LCD, make sure you installed the u8glib...
View ArticleRe: please help just another new strugling
Hi thanks for the reply i have downloaded U8Glib and added to my libery dose the need to be put in anywhere secific as if i add it to the sketch it puts it in at the very top of the config.h file....
View ArticleRe: 230K Thermistor
Quotearthurwolf Quote762x51 I like the Smoothie Smoothie likes you too then :) Yes it does - Much more than the RUMBA I have decided that the Smoothie is the best choice. A little more expensive but...
View ArticleRe: DEFAULT_AXIS_STEPS_PER_UNIT Above 999 - T8x2 Leadscrew
Thanks for the replies... I ended up switching to 8mm 4 start leadscrews... much better. Thanks for all the help Marcos.
View Article