Re: Extrusion Issues when updating to Marlin 1.1
find in configuration.h // For direct drive extruder v9 set to true, for geared extruder set to false. #define INVERT_E0_DIR false The comment is crap as it depends which way around your stepper plug...
View ArticleMarlin 1.1.4
Now I have two Hictops one 12volt and One 24volt. They have the same controller card they were both upgraded to Marlin 1.1.4-RC6 - they both have different problems. The only firmware lines that are...
View ArticleRe: RRD 2004 Configuration
This is what I use in Marlin 1.1.4 #define LCD_LANGUAGE en #define DISPLAY_CHARSET_HD44780 JAPANESE #define SDSUPPORT #define SPI_SPEED SPI_HALF_SPEED #define SD_CHECK_AND_RETRY #define...
View ArticleRe: Extrusion Issues when updating to Marlin 1.1
Dust, That was it!!! And, I laughed when I saw your reply. I looked right at that setting and thought for sure (because of the comment) that it did not apply. But, I flipped that bit and sure enough,...
View ArticleRe: RRD 2004 Configuration
@Roberts_Clif many thanks for the reply :) I've tried various combination of settings for both the ENCODER_PULSES_PER_STEP and ENCODER_STEPS_PER_MENU_ITEM but unfortunately, I've had no luck :( Seems...
View ArticleRe: Marlin 1.1.4
I have Changed Bed leveling from Linear to Bi-linear saving 6812bytes still CRC error but different number "-118." Still " Endstops Z " on display. Have dropped the Memory use below 50% Still CRC on...
View ArticleRe: RRD 2004 Configuration
Do you have menu items that appear to have garbage in the lines at times. One time ok the next time garbage.
View ArticleM218 Z-Offset without DualCarriage or SwitchingExtruder
Hello! My multi-extruder printer can switch complete toolheads automaticly. They are clipped on with magnets and can be interchanged by moving to a certain position. That way, the height of the...
View ArticleRe: M218 Z-Offset without DualCarriage or SwitchingExtruder
I finally got it to work. The trick was to activate the movement of the z-axis when toolchanging. The change in the post above has to be done as well (in order to accept the offset). You have to make...
View ArticlePrinter slight pause during prints
Hi Guys While my print is printing the printer will do a slight ( 2 second ) pause and carry printing. It seems to happen when it move to other parts of the print. I have changed & bought a new...
View ArticleRe: Marlin 1.1.4
If I include the configuration.h file someone can see if a mistake is there. [attachment 97620 Configuration.h]
View ArticleRe: RRD 2004 Configuration
There is no garbage on any lines at all. I'm wondering if maybe the encoder is either faulty or not correctly soldered. I think I'll try resoldering the encoder, and/or create a separate Arduino...
View ArticleMarlin 1.1.4 UBL issue
Hello, im trying to configure UBL on my Sunhokey I3 with capacitive probe connected to z- min endstop G28 works as expected. I have 3X3 mesh set in FW. I'm following [marlinfw.org] for setup. The...
View ArticleSilicon Bed Heater Temperature Problems with Marlin 1.1
I bought a new silicon bed heater and aluminum bed does not appear to be getting accurate temperature readings. The product docs clearly states that the thermistor is a "NTC 3950 Thermistor built in...
View ArticleRe: Silicon Bed Heater Temperature Problems with Marlin 1.1
3950 Thermistors are generally 100K @ 25C, Heat water to 25C measure the Resistance. Could be a bad or maybe it is the defective thermister. Item:NTC Thermistor Model:B2-100-3950-1 R @ 25C: K 100K-1%...
View ArticleRe: Silicon Bed Heater Temperature Problems with Marlin 1.1
"IR Temperature gun" are crap They cannot measure reflective or metallic surfaces (and most of them the "laser" pointer is nothing like where its looking) get a thermocouple eg [www.aliexpress.com]
View ArticleRe: Jennyprinter 3 , which firmware is correct?
Hi Wilfred, did you found a new/better Version of Firmware for your Printer? What Do you think about this Printer? I think about buying this Printer too. Regards Christian
View ArticleRe: Silicon Bed Heater Temperature Problems with Marlin 1.1
QuoteDust "IR Temperature gun" are crap They cannot measure reflective or metallic surfaces (and most of them the "laser" pointer is nothing like where its looking) get a thermocouple eg...
View ArticleRe: Silicon Bed Heater Temperature Problems with Marlin 1.1
I'll have to find/replace my multimeter now :) Yeah, it could just be a bad/defective thermistor.
View ArticleRe: Silicon Bed Heater Temperature Problems with Marlin 1.1
Thanks for the link, Dust! They're pretty cheap, I'll have to pick one up!
View Article