Clik here to view.
Marlin and Full Graphics Smart Controller
Hello guys, i've installed a RepRap Full Graphics Smart Controller on my i3 Hephestos but im having a bit of an issue with it. Everything works but the screen (after a few minutes, sometimes seconds...
View ArticleRe: Marlin and Full Graphics Smart Controller
There have been a lot of LCD changes since v1.0.2 It would be helpful if you brought up the current version at: [github.com] But with that said... There have been some number of faulty LCD display...
View ArticleRe: Marlin and Full Graphics Smart Controller
QuoteRoxy There have been a lot of LCD changes since v1.0.2 It would be helpful if you brought up the current version at: [github.com] But with that said... There have been some number of faulty LCD...
View ArticleBLTouch & Delta Issue
I'm just building an Anycubic Kossel plus and have added a BLTouch Smart probe. I'm running on a very late snapshot of bugfix-1.1.x. I've got got an issue in that when doing an delta auto calibration...
View ArticleRe: Marlin and Full Graphics Smart Controller
First check your wires and make sure they are not running for long distances next to high current wires. You may even want to isolate the LCD Panel's wires just to test for electrical interference by...
View ArticleDisplay the Measurement Result during Bed Leveling
Is it possible do display the measurement result of each point during bed leveling on the LCD screen? Watching these values during bed leveling would give a good information about the alignment of the...
View ArticleRe: BLTouch & Delta Issue
have a look in configuration_adv.h and make sure 'safe homing' is enabled
View ArticleRe: Marlin and Full Graphics Smart Controller
QuoteRoxy First check your wires and make sure they are not running for long distances next to high current wires. You may even want to isolate the LCD Panel's wires just to test for electrical...
View ArticleRe: BLTouch & Delta Issue
I have Z_SAFE_HOMING defined in configuration.h. I don't see any reference to safe homing in configuration_adv.h. Is this the setting?
View ArticleStuck on STOPPED
I am running Marlin 1.1.2 on a Tevo Tarantula with BLTouch. I mistakenly unplugged the AC to the power supply while it was running a print job. Now I cannot home the Z axis. The LCD display shows...
View ArticleRe: Marlin and Full Graphics Smart Controller
QC stickers are on everything from china.. none of it has had any checking...
View ArticleRe: BLTouch & Delta Issue
Yes sry, thats the one i meant, but seems that is not your problem tho.
View ArticleUnderstanding my flavor of Marlin
I have downloaded a copy of the Marlin firmware version currently installed in my printer (Lulzbot TAZ 6) mostly for my own education. I can look at the source code but because of the heavy dependency...
View ArticleCan't compile Marlin
Hi, I try to compile Marlin for my Anet A8 and get an error. What do I do wrong?
View ArticleRe: Understanding my flavor of Marlin
I'll answer my own question in case this topic interests anyone else. Microsoft Visual Studio Community Edition is free as is Arduino IDE for Visual Studio (http://www.visualmicro.com/). You can open...
View ArticleRe: Can't compile Marlin
The error tells you what to do...only enable one type of printer configuration. It is telling you that all those printer configurations are enabled but only one active is allowed.
View ArticleRe: Display the Measurement Result during Bed Leveling
If you use the console to send the g29 code the results are printed out in console.
View ArticleRRD 2004 Configuration
Hi I recently acquired a RAMPS 1.4 board including a RepRapDiscount Smart Controller for Arduino Mega 2560 with a 20x04 LCD screen, and have installed Marlin 1.1.4 I'm having a slight configuration...
View ArticleTwo Y_min stops and homing the extruder
Hi guys, currently I'm working on a project that involves two Y motors. It's basically a gantry like this: [youtu.be]. But with two Y motors instead of the coupler + linear rod setup. I made the...
View ArticleExtrusion Issues when updating to Marlin 1.1
I have an “old” printer (Bukobot circa 2014) which has an Azteeg X3 board running Marlin from about that same period. I don’t have the code that the board was installed with, but I do have the...
View Article