Re: Silicon Bed Heater Temperature Problems with Marlin 1.1
I find it interesting that the thermistor difference (at ~ 16deg) is so consistent. When set to 55deg, the measured temp is about 39deg. When set at other temps, the difference is always ~16 off. I...
View Articledual extruder upgrade problem
I have upgraded my Hictop 3DP08 to dual extruder. It now has 2 extruder stepper motors and XCSOURSE dual J head nozzle extruder kit which has 2 nozzles, 2 thermistors and 2 heaters. I have configured...
View ArticleRe: dual extruder upgrade problem
MINTEMP fail is the thirmistor not reading room temperature... heating will be disabled till this is fixed.
View ArticleRe: Jennyprinter 3 , which firmware is correct?
What is the number on the large black chip? its its not atmel 1284 or atmel 2560... marlin will be an issue.. It does look like a Ultimaker Generation 2 control board... so motherboard BOARD_ULTIMAIN_2
View ArticleRe: Jennyprinter 3 , which firmware is correct?
Still struggling with better firmware. "I can upload the actual FW that is installed right now if that helps." This could be very helpfull Michael:) The rest of the printer is pretty fine, the only...
View ArticleHow can i move a menue item to another position?
Can anyone please explain me how can i change the ultralcd.cpp to move the menu item Main -> Prepare -> Preheat PLA "Preheat PLA" one level up or to the main menu ? many thanks!
View ArticleRe: dual extruder upgrade problem
Thanks for the tip. I think the information I gave you was slightly misleading. This is my scenario... I am confident that all the hardware ( both thermistors and both heaters ) function correctly all...
View ArticleRe: dual extruder upgrade problem
The thermisters have to be unplugged before you can measure their resistance room temp 25C should be about 100K ohms. What is the reading on your LCD for your hot-ends, if this temperature is below...
View ArticleRe: dual extruder upgrade problem
I checked the thermistors with a meter and both were around 100K ohms. I checked them at the motherboard connector to be sure there was no break in the wiring. The LCD reads 22C which is about right....
View ArticleRe: Jennyprinter 3 , which firmware is correct?
Hi Wilfred, thanks for the reply, what is the Problem with the delivered original Firmware? Regards Christian
View ArticleTravelING_FADE_HEIGHT availalbel in Marlin 1.1.x?
Hi at all, is there any possibility in the Marlin FW to lift the nozzel, during a print while traveling from one point to another one. So the nozzel don't hit any of the all ready printed object, when...
View ArticleRe: TravelING_FADE_HEIGHT availalbel in Marlin 1.1.x?
This is a slicer option, not firmware.
View ArticleExtruder 2 not working
I have upgraded my Hictop 3DP8 printer to dual extrusion, using the XCSOURCE dual J head nozzle extruder, so it now has 2 nozzles, 2 thermistors and 2 hot ends. I can not get the 2nd hot end to heat...
View ArticleRe: Extruder 2 not working
Motherboard BOARD_RAMPS_14_EEB knows nothing about D7 EEB sets D8 heated bed, D9 hotend 1 and D10 hotend 0 use Motherboard BOARD_MKS_13 then it knows about D7 and becomes // Power outputs EFBF or EFBE...
View ArticleMirrored text fix, I missed something?
Hello, I recently rebuilt my printer, it was a GeeeTech ME Creator (original version) I basically tore it apart and started over, Bowden J-Head, Ramps 1.4 with TMC2100 lead screw etc etc etc Got rid...
View Article1.1.5 getting mesh bed leveling working
I just rebuilt my printer and setup Marlin 1.1.5 from scratch. I enabled #define MESH_BED_LEVELING and now I see the bed leveling option in my LCD panel menus. BUT!!! All it does is home all axis.......
View ArticleRe: Mirrored text fix, I missed something?
Let see If this will help Did you do a M502 and a M500 to save the new Configuration Or In Marlin 1.1.5 Click menu Click Control Click Initialize EEProm This clears settings out and loads the new...
View ArticleRe: 1.1.5 getting mesh bed leveling working
* - MESH_BED_LEVELING * Probe a grid manually * The result is a mesh, suitable for large or uneven beds. (See BILINEAR.) * For machines without a probe, Mesh Bed Leveling provides a method to perform...
View ArticleRe: Mirrored text fix, I missed something?
I was not doing the changes as temp via mcodes and then saving to eeprom. I was changing the arduino sketch in Configuration.h and uploading it each time.
View ArticleRe: Mirrored text fix, I missed something?
I have been thinking about it all day and I came up with a theory. Perhaps the end stop logic has reversed as a result of the axis or endstop values changing. I can test this by holding the end stop...
View Article