Re: Mirrored text fix, I missed something?
Killing old settings is annoying, but normally when updating firmware users are aware that their old settings may not roll over, and they should Initialize EEProm. This is one reason that they Placed...
View ArticleRe: Mirrored text fix, I missed something?
I have not once set anything in the eeprom, its blank. I have not yet enabled the eeprom even. M500 M501 M502 will not do a thing. Its just not enabled.
View ArticleRe: 1.1.5 getting mesh bed leveling working
ok.........how does any form of auto bed leveling work with no probe? I think I have figured this one out tho. Two options need to be enabled for manual bed leveling. #define MESH_BED_LEVELING and...
View ArticleRe: Jennyprinter 3 , which firmware is correct?
IF that black chip is a STM32F407VET6 then its an ARM based 32bit CPU and the common 8 bit Marlin FW will not work. There are forks of Marlin developed for 32bit systems but you would have a steep...
View ArticleRe: Mirrored text fix, I missed something?
Quotequite Change INVERT_Y_DIR false to true and Change Y_HOME_DIR -1 to 1 and disable #define USE_YMIN_PLUG and enable #define USE_YMAX_PLUG only thing left to do is move the endstops from the...
View ArticleRe: Mirrored text fix, I missed something?
DUST: This appears to be what I missed. To verify- Your saying the end stop switch that was Y-Min and is now Y-Max has to be physically plugged into a different set of pins on the Ramps 1.4?
View ArticleClik here to view.
Re: Mirrored text fix, I missed something?
Ya I think you are right :) FCF2INLIGWJY4U7.MEDIUM.jpg so simple.... Thanx much!!!!
View ArticleRe: 1.1.5 getting mesh bed leveling working
You manually lower the nozzle to a piece of paper, click the menu button it goes to the next location. you lower the nozzle to the piece of paper ect... Until you reach the end of the bed. usually...
View Articlehow g33 works?
My probe I installed is far away from the nozzle (offset -x45 y17), maybe my endstop z or hotbed is not level, the result is useless. My question is how to level the endstops? is G33 my solution? if...
View ArticleRe: Jennyprinter 3 , which firmware is correct?
Hello, I think the two printers in this thread are different Models The Printer from Micstar is the 2016 Model and the board looks like a UM Board. The Printer from Wilfred is the new 2017 Model....
View ArticleRe: 1.1.5 getting mesh bed leveling working
yes Cliff, but that is manual leveling, a procedure I have done dozens upon dozens of times on this printer before I changed out the electronics. My problem is the menu selection does not activate the...
View ArticleRe: Mirrored text fix, I missed something?
Just another thanx to DUST!! That did fix it!!
View ArticleRe: Jennyprinter 3 , which firmware is correct?
Quotec.radi Hello, I think the two printers in this thread are different Models The Printer from Micstar is the 2016 Model and the board looks like a UM Board. The Printer from Wilfred is the new 2017...
View ArticleRe: 1.1.5 getting mesh bed leveling working
This is My Marlin 1.1.5 Code for Linear/Bilinear Bed Leveling #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN #define FIX_MOUNTED_PROBE #define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of...
View ArticleRe: 1.1.5 getting mesh bed leveling working
Upload your code I will take a look for you!
View ArticleRe: 1.1.5 getting mesh bed leveling working
QuoteRoberts_Clif Upload your code I will take a look for you! Thanx for the offer Clif, I got it tho. It was just the //#define LCD_BED_LEVELING needed to be enabled. all good now.
View ArticleRe: Marlin 1.1.4 UBL issue
First... a 3 x 3 mesh is not going to offer much accuracy. Really... you should consider going with a 10 x 10 mesh. Second.... It is very important that you have your printer setup correctly to print...
View ArticleMarlin 1.1.5
I have a unique problem It involves "Endstop Trigger reporting" I get an error Using a Proximity sensor TL_M3W 'NPN' NC as a Z-Axis endstop. using these lines of code. #define...
View ArticleRe: Marlin 1.1.5
I re-flashed both 3D Printer with Marlin 1.1.5, Now one works, the other one still displays Display " Endstops Z ", Before you say it I swapped the Controller with a spare controller still does not...
View ArticleClik here to view.
Inductive Z-probe not seen by Marlin / RAMPS 1.4
Hi, I just replaced my microswitch Z-min switch (which was just on there for testing and it works) with a "SN04-N 4mm Inductive Proximity Sensor Detection Switch NPN NO DC 10-30V" from ebay. I wired...
View Article