Re: Problem With BLTouch Sensor
Quotejaded You can't have repetier host connected to your printer at the same time you are trying to send firmware through arduino. You must disconnect repetier host from the printer before sending...
View ArticleRe: Problem With BLTouch Sensor
Everything is now nearly working. The response from the M280 commands are as expected. However the probe status remains fixed at activated - it doesn't change regardless of any instruction. I imagine...
View ArticleRe: Problem With BLTouch Sensor
Quotekmxsoft Everything is now nearly working. The response from the M280 commands are as expected. However the probe status remains fixed at activated - it doesn't change regardless of any...
View ArticleRe: Problem With BLTouch Sensor
It isn't triggering. When I put the printer in homing mode, X & Y do the necessary, however the BLTouch probe on Z does not trigger so I have to power off to stop the Z crashing into the bed....
View ArticleRe: Problem With BLTouch Sensor
In your config.h Quote#define Z_MIN_PROBE_ENDSTOP_INVERTING true // set to true to invert the logic of the probe. I think you need to change this to false as the bltouch is like a NC endstop and gives...
View ArticleInfo about adding Capacitive Bed Leveling
Hi. I want to connect a Capacitive Probe to the RAMPS 1.4 of a Prusa i3 Hephestos BQ. Many tutorial online tend to use the Z-Min endstop for send the triggered signal. Reading the Configuration.h at...
View Articlebrauche Hilfe mit Marlin
Hallo da draussen, beim kompilieren der Marlin Software bekomme ich folgende Fehlermeldung: In file included from sketch\ultralcd.cpp:78:0: sketch\ultralcd_impl_HD44780.h: In function 'void...
View ArticleRe: Problem With BLTouch Sensor
Quoteobewan In your config.h Quote#define Z_MIN_PROBE_ENDSTOP_INVERTING true // set to true to invert the logic of the probe. I think you need to change this to false as the bltouch is like a NC...
View ArticleRe: Problem With BLTouch Sensor
And to make matters more difficult... Some of the BL-Touch clones actually have an inverted signal. If you have a real BL-Touch, you can ignore this message. But if it is possible you have a knock...
View ArticleRe: Problem With BLTouch Sensor
QuoteRoxy And to make matters more difficult... Some of the BL-Touch clones actually have an inverted signal. If you have a real BL-Touch, you can ignore this message. But if it is possible you have a...
View ArticleRe: brauche Hilfe mit Marlin
Hast du vielleicht mehrere LCD-Treiber definiert? Es sollte nur der UltraLCD Treiber aktiv sein und SD-card support. Zumindest wenn du ein 20x4 LCD hast und kein graphic display.
View ArticleRe: brauche Hilfe mit Marlin
vielen dank für die Antwort habe lediglich das falsche Displayausgewählt Menü wird jetzt angezeigt aber ich kann zwar den Drucker verbinden aber es werden keine Werte angezeigt Im Display werden zwar...
View ArticleRe: brauche Hilfe mit Marlin
was mir jetzt noch aufgefallen ist,ist das der Mega ziemlich heiz wird auch ohne angeschlossene Motoren
View ArticleRe: brauche Hilfe mit Marlin
Um die Stepper testen zu können, musst du erst den Drucker mit "G28" homen. Oder du sendest z.B. "G92 X180 Y0 Z10 " damit der Controller weiss, wo er ist. ( Oder glaubt es zu wissen ;) ) Der Extruder...
View ArticleRe: brauche Hilfe mit Marlin
habe denn Fehler zwischenzeitlich schon lokalisiert beim Ramps wurde bei der Fertigung die Leiterbahn zwischen D1(am Mega D0 = RX) angebohrt was dazu führte das die Späne aus Vcc = 12V gelegt wurden....
View ArticleRe: brauche Hilfe mit Marlin
ach ja die Bewegung erfolgt nur in eine Richtung (+) Test über Display
View ArticleRe: Problem With BLTouch Sensor
I've given up with the BLTouch and am now using a capacitive sensor instead. It works remarkably well, detecting the print surface about 4mm away. Whilst I had tried to use a capacitive sensor...
View ArticleRe: brauche Hilfe mit Marlin
kurze Nachlese: das Problem mit der Drehrichtung lag an den Endstops Ausgetauscht und gut Danke für die Hilfe melde mich noch mal
View ArticleUmbau K8200
Hallo da draußen, nach dem sich bei meine K8200 die Elektronik und der komplette Extruder verabschiedet hat habe ich beschlossen die defekten Teile auszutauschen. Da für die beiden Teile aber ca....
View ArticleRe: Umbau K8200
Quote J-Head V6 Hot End (3mm / 0,5mm) Hat das Teil einen Lüfter, der auf die Kühlrippen bläst? Es hört sich so an, daß das Filament zu heiß ( weich ) wird und sich dann oberhalb des eigentlichen...
View Article