Z probe first probe nowhere near bed?
This is mystifying me. Using Marlin firmware that came with my Sintron Mini Kossel, been running fine for months. Self levelling probe was doing what it is supposed to. Printing speed and quality was...
View ArticleRe: Z probe first probe nowhere near bed?
Wow! You have an ancient version of Marlin on that machine. You will find the Auto Bed Leveling has become much more sophisticated over the last 2 years. You need to grab [github.com] and cross your...
View ArticleRe: Z probe first probe nowhere near bed?
I wouldn't argue with that, lol, but as the existing firmware was working ok (a bit of a nightmare to configure it, but hey I learned a lot about Delta printers) I had no reason to update anything. My...
View ArticleRe: Z probe first probe nowhere near bed?
Click the green button and download the zip,it will contain the whole firmware package. Yes you will need to make changes to the configuration.h before you upload the new firmware to your controller.
View ArticleRe: Umbau K8200
wie sich in der letzten Nacht herausgestellt hat ist eins der Probleme der Bowdenschlauch. Durch das perforieren des Filamentes schafft es der Extruder nicht mehr dieses durch den Schlauch zu drücken....
View ArticleRe: Printing Above Bed 1.1.4
I have the same problem and searched everywhere inside the configuration-files. Z-Axis homes successfull near the bed and then lifts to 10 mm height. Think this is normal to marlin, but when printing,...
View ArticleRe: Umbau K8200
PS: Du weißt, das es hier auch ein Deutsches Unterforum gibt? Hier wird eigentlich nur englisch geschrieben... smiling smiley hab ich leider nicht gefunden danke für den Hinweis gibt es eine...
View ArticleRe: Z probe first probe nowhere near bed?
Many thanks for offering assistance, but I have found the source of the problem. It is the infamous Sintron probe. Having fitted the ED3 the fins are wider, and these interfere with the spring. This...
View ArticleM42 code not Working
Hello, M42 code isn't working. Can't switch AUX Pins or Servo Pins. FAN Pins are protected. Error: Protected Pin. I delet the sensitive List (FAN). Error message doesn't come, but still doesn't work....
View ArticleRe: M42 code not Working
What syntax are you using? egs? What board are you using? guessing a ramps 1.4, NB D0 and D1 on aux-1 are the serial port, rx and tx, so you cant use those.... D4,D5,D6,D11 on servo should all be...
View ArticleRe: M42 code not Working
Board is an TriGorilla 3D ATMEGA2560-16U Chip, replaced RAMPS1.4 + Mega 2560 Firmeware is Marlin attached to Pronterface
View ArticleRe: Umbau K8200
habe das Problem wahrscheinlich lokalisieren können die Andruckspannung des Extruders ist zu hoch. Dadurch wird die Antriebsachse verkantet also mehr Last Momentan läuft noch ein Druck werde den...
View ArticleClik here to view.
Re: M42 code not Working
totally differnt pinout... (well just a few differences) TE627-E-10-9.jpg
View ArticleRe: M42 code not Working
Yes... here: (its' the config from producer) //// The following define selects which electronics board you have. Please choose the one that matches your setup // 10 = Gen7 custom (Alfons3 Version)...
View ArticleRe: M42 code not Working
the thing is, 3d printing with this firmware works fine. don't understand---differnt pinout
View ArticleRe: New Menu Item to Load / Unload Filament
I did it with a Gcode file than runs from SD card; M109 S175 ; wait extruder temp reaches 175 for ABS G91 ; relative coords G1 E-20 F500 ; retract 20 slow f500= 8mm/s G1 E-800 F6000 ; retract 800...
View ArticleEnable display of thermistor 2 value on single extruder RampsEFB
As title. I'd like to use T02 input and just display its temperature value on a graphic display. I see it was raised in Marlin github as a feature request a while ago but seemed to go nowhere. I saw a...
View Article