Re: Complies but with errors
Ok thanks. I tryed that in S3D and it always wentry to the rear right. I will have a look at it again when I put it back together (in bits fitting piezo self leveling to it) Thanks for the help/info,...
View ArticleRe: UBL explained please
Along the lines of ubl... I have been reading whatever documentation and old threads I can dig up and (due to the age of what I found) I am still a bit confused on ubl. I am currently using the latest...
View ArticleRe: UBL explained please
QuoteSo I am wondering, what is there about ubl that would make it more desireable over bilinear and how can it be done as automagically as possible? Probably the single best reason is the integration...
View ArticleRe: UBL explained please
Thanks roxy. I have no problems overall using bilinear. I guess after converting to bowden/e3d I can see more of the bed now under the nozzle due to the relocation of fans and ducts. This allowed me...
View ArticleNew Menu Item to Load / Unload Filament
I was surprised to see that there was an option to have a menu item to toggle case led on/off. Cool. I would like to see something similar for Load / Unload filament that basically heats up the head...
View ArticleRe: UBL explained please
Quotejaded Thanks roxy. ... Again though, it would be great to have the g26 feature working with bilinear. The UBL files all start with ubl_ in the file name. The G26_Mesh_Validation_Tool.cpp file did...
View ArticleRe: New Menu Item to Load / Unload Filament
The code is not mature yet. But you might want to check out M701 and M702: [github.com]
View ArticleRe: Marlin configurator
released new version 2.7.8 fixed: console 3d Command menu added: - external upnp access - ability to use phone as web cam - simultaneously working - store current config - upload stored config
View ArticleRe: Garbled text REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
Can I see picture of how your LCD cables run to the Controller
View ArticleRe: Garbled text REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
Ignore this message... I thought something else was being asked...
View ArticleABL Averaged Probing
I recently paired an Anet A8 with a Geeetech BLTouch clone using SkyNet3D (Marlin base). Although accurate most of the time (within 40 microns) it would occasionally be out up to 200 microns. This...
View ArticleRe: ABL Averaged Probing
(tu(tu)(tu)) sounds like a good idea, i have one of these probes and can confirm that occasionally it will throw up a spurious result.
View ArticleProblem With BLTouch Sensor
I have recently built a Hictop 3D printer: [www.amazon.co.uk] All working fine. Have tried to add a BLTouch sensor but have run into difficulty. Have replaced the main control board with an MKS 1.4:...
View ArticleRe: Problem With BLTouch Sensor
You should use M280 P0 S10 and M280 P0 S90 to verify the BL-Touch is working. If those two commands do not deploy and retract the pin, the BL-Touch is probably not connected up to Servo-0 like it is...
View ArticleRe: Problem With BLTouch Sensor
Thanks for that. Is there a way to send gcode commands to a 3D printer interactively? I have Cura and Simplify3D available but they don't appear to offer interactive options.
View ArticleRe: Problem With BLTouch Sensor
you can use repetier host or mattercontrol both are free and will manually control the priter via usb
View ArticleRe: Problem With BLTouch Sensor
Simplify3D's Machine Control Panel window has a tab labeled Communication. Once you are connected to the printer you can type any string you want at the bottom and press Send. You will see the...
View ArticleRe: Problem With BLTouch Sensor
Also... The LCD Panel can do things with the BL-Touch probe. So you might be able to test things that way.
View ArticleRe: Problem With BLTouch Sensor
Thanks all - some good info there which I am very grateful for. I downloaded and installed Repetier host. Now Arduino is refusing to upload new firmware to the printer - it compiles fine but fails...
View ArticleRe: Problem With BLTouch Sensor
Quotekmxsoft Thanks all - some good info there which I am very grateful for. I downloaded and installed Repetier host. Now Arduino is refusing to upload new firmware to the printer - it compiles fine...
View Article