Re: Z axis Not working well
Hello Obewan, no translation/translator now! I have tested with 3 and the Z motors were complaining and buzing! so now on 2.5 it is okee and I start A test print forloking waht the printer wil do. ....
View ArticleRe: Which version to use
Yes... If you are bringing up a new printer... Use bugfix_v1.1.x
View ArticleAuto bed leveling, now what
Hi, I finally installed auto inductive sensor 4mm or 8mm , can't remember now. We'll now what, how do make my 3d printer do a auto leveI before print somenthing, how do adjust the nozzle if it's to...
View ArticleRe: Auto bed leveling, now what
The first step is to get your Z-Probe_offset_from_extruder set exactly correct.... That is very important. Once that is set correctly and you can print a small calibration cube (with no bed leveling...
View ArticleRe: Auto bed leveling, now what
Hi, as right now I have the sensor set to autolevel. What now , I already set the sensor offset in the Marlin firmware. The g code to auto level is g29. Now after autolevel, how do adjust the z axis...
View ArticleRe: Auto bed leveling, now what
You dont adjust the code for offset. You do it in the firmware. You said you set the offset already in the firmware? If its too high then your offset is not correct. Adjust and try again.
View ArticleRe: Auto bed leveling, now what
hold on , i am lost . i set the distance from the extruder to the sensor x and y. where i am looking at for the z offset in the config.h ?? BTW :thank you for the help.
View ArticleRe: Auto bed leveling, now what
You want to adjust Z_PROBE_OFFSET_FROM_EXTRUDER such that it will print a small calibration cube (in the center of the bed) with no auto bed leveling active. If you can do that, you are ready to start...
View ArticleRe: G-Code Script
you xmin should be "0" not "-46" "-46" is your x offset - in other words how far away your hotend finishes from xmin when you home.
View ArticleHow detect thap PID working for the bed?
Hello there! My nozzle have PID activated of course. When it reach the right temp then the LED for it on the mainboard start flicker and the temp is perfect, stable. My heated bed also had PID...
View ArticleMarlin 1.1.1.
Hey guys, so i finally upgraded from marlin 1.0.0 to 1.1.1 and i am struggling a little bit. The main thing is auto level, i tell it to home and it sits above the bed after homing i try to move the...
View ArticleSetting RGB LED values on boot
I have my custom built 3d printer working quite nicely now with Marlin and RAMPS, and the RGB LED support is great since getting it working with help on this forum. What I would like to do is have the...
View ArticleRe: Setting RGB LED values on boot
can't try it at the moment, but give this a try in Marlin_main.c line 12708 (in my version) is the following #if ENABLED(RGB_LED) || ENABLED(RGBW_LED) SET_OUTPUT(RGB_LED_R_PIN);...
View ArticleRe: Setting RGB LED values on boot
Cheers, will give it a try in the morning as I am just off to work. :)
View ArticleRe: Crazy homing behavior on Marlin 1.1.1
Ok!!! The program I used to port the configuration values did not recognized the section for MIN_ENDSTOP_INVERTING due to the HUGE differences in some parts of the file. The printer believed it was...
View ArticleRe: How detect thap PID working for the bed?
I'm not sure I understand your problem, you are saying there is no way to set/save the values after you tested the bed or that there is no place to view the current values? I use Marlin and it's just...
View Article