How is babystepping supposed to work with UBL?
I've, after significant effort and many tries, gotten UBL up and running. I'm confused, however, about two things. First, what am I supposed to put in the start g-code in my slicer? Previously it was...
View ArticleRe: Linear Advance vs Advance
Also, is linear advance still incompatible with Cura (2.5)?
View ArticleRe: How is babystepping supposed to work with UBL?
Well... There are a couple of answers... You have a choice whether UBL is active at reset or power up. I always run my print with UBL automatically enabled. You do that by activating UBL (G29 A) and...
View ArticleSD CARD PROBLEM - Marlin 1.1.0 RC8
Hi all, I've a problem with the sd card reader on my reprap discount lcd panel. I tried with a 2gb and a 4gb (FAT/FAT32 formatted) but I always get "no sd card" on lcd menù. In the info screen I can...
View ArticleRe: marlin 1.1.0 rc7 and inductor sensor 12vdc
Need a bit more info pls what controller board ? what probe ? how is the probe connected ? looking at your endstop settings above, you have all endstop pullup resistors disabled ?
View ArticleRe: User guide to UBL?
The UBL getting started guide is now available. We will be changing the firmware so that the LCD is all that is needed to do 99% of the UBL bed leveling. The changes should be in the bugfix-1.1.x...
View ArticleRe: marlin 1.1.0 rc7 and inductor sensor 12vdc
hi Obewan, sorry i forgot , its a ramps1.4 i use pololu 8825 driver and inductive sensor its a LJ12A3-4-Z/BX 6-36v NPN , use two resistor to 10k 20k to lower voltage to 5v signal from sensor connected...
View ArticleRe: marlin 1.1.0 rc7 and inductor sensor 12vdc
Your connections look good and using the resistor devider,you dont need the Z endstop resistor enabled but you will need to enable the X and Y min endstop pullups. Quotewhen i get a peace metal close...
View ArticleRe: marlin 1.1.0 rc7 and inductor sensor 12vdc
ok, sorry for the mix up firmware with rc5 to rc 7, i post the wrong version of config. the lcd screen its went blank, light up, wont show anything , i can move the axis with repetier-host, i press...
View ArticleRe: Enabling #define RGB_LED results in compiler error
QuoteAlpinaV8 QuoteDust Good spotting... I've updated the github issue with these details. One day ill learn how to submit the fix to the real code... *unhelpful remark removed* I recommend Visual...
View ArticleEnable the Z steppers at startup
I everyone! First of all I would like to thank the Marlin team for all the work they did on 1.1.0 version! I have a little issue that I hadn't before updating marlin. My bed is heavy and falls down...
View ArticleRe: marlin 1.1.0 rc7 and inductor sensor 12vdc
ok , i am back on. lcd works. i setup the wrong board on config.h i setup ramp_14EFB , i also setup the pin z_probe_pin to 18 pin18 its the z_min_pin do i need to disable the z_min_pin or not. the z...
View ArticleRe: Enable the Z steppers at startup
You could add a pull-down resistor to the enable pin of the z-drivers. That way it is ON all the time.
View ArticleUsing relays for hotend and bed gives unexpected results
Hi everyone! I have a RAMPS 1.4 board. Today I connected all the wires, including the ones for heated bed and extruder, providing double power supply to the RAMPS shield. I started a print, everything...
View ArticleRe: marlin 1.1.0 rc7 and inductor sensor 12vdc
ok, update firmware to 1.1.0.1 and works it. i try the old version rc 5 and rc 7 and work too. here my mistake i did. my sensor its npn no 6v-36v and a ramps 1.4 board. first mix up firmware board...
View ArticleRe: Using relays for hotend and bed gives unexpected results
This is how PID works.... check your PIDTEMPBED settings A real relay will a) drive you batty with clicking b) eventually due to sparking contacts it will one day fuse in one position. a external...
View ArticleRe: Using relays for hotend and bed gives unexpected results
Hi Dust, I think I wasn't able to explain nicely the issue. The issue is with the hotend. The heated bed behaves correctly, it gets powered on and off as expected without making noise. The hotend gets...
View ArticleRe: Using relays for hotend and bed gives unexpected results
As Dust said, use a external mosfet on a heatsink, a relay WLL NOT WORK on the hotend.
View ArticleRe: Using relays for hotend and bed gives unexpected results
Hi obewan, so a plain relay will not work, I'll get a SSR relay, which is made which has no mechanical parts. DC SSR Relays are based on MOSFETs, so I'll buy one of them instead of doing the circuit...
View ArticleMarlin firmware using universal g code sender ?Is it possible?
I currently am running a highly modified version of marlin firmware with a megatronics v2.0 controller ..Wanting to switch over to using ugs platform as it has keyboard jogging features and other...
View Article