Re: Bed Leveling RC8
Quoteobewan In configuration.h #define X_PROBE_OFFSET_FROM_EXTRUDER -22 // X offset: -left +right [of the nozzle] #define Y_PROBE_OFFSET_FROM_EXTRUDER 0 // Y offset: -front +behind [the nozzle]...
View Articletrue bed levelling - not bed level compensation - Does this already exist?
Dear all, I am new to Marlin, but comfortable with programming. I require a "Bed Leveling Calibration routine", which would function by using a Z probe, measuring 3 points on the bed, and then...
View ArticleRe: true bed levelling - not bed level compensation - Does this already exist?
If you are going to manually turn the appropriate screw to physically adjust the bed, you may be able to use the Topographical map of the grid leveling system. I introduced that almost 3 years ago:...
View ArticleRe: Bed Leveling RC8
QuoteEddiie Great! So RCBugfix is newer than RC8? Is RCBugfix always newer? Seems there was a RC6 bug fix too. Yes! RCBugFix is an 'improved' version of RC-8. That has been the methodology this entire...
View ArticleRe: Bed Leveling RC8
QuoteEddiie Great! So RCBugfix is newer than RC8? Is RCBugfix always newer? Seems there was a RC6 bug fix too. Yes! RCBugFix is an 'improved' version of RC-8. That has been the methodology this entire...
View ArticleRe: true bed levelling - not bed level compensation - Does this already exist?
I've seen some people experimenting on doing that over the years. For instance the sparkcube does it : [www.youtube.com] but I think they use Repetier firmware
View ArticleAuto Bed Leveling RC8 - Z axis goes up while homing
Hi, I have a problem with the auto bed leveling feature. The z axis goes up when I'm homing z. So the inductive sensor (LJC18A3-H-Z/BX) goes away from the heated bed. The motor direction is correct,...
View ArticleRe: Bed Leveling RC8
OK, Moved to RC8 Bug Fix Moved Z probe to Z Min Power on, Control -> Auto Home ................... Z goes UP a few mm, then X homes and Y homes. An error is displayed - G28 Z Forbidden ?? Will do...
View ArticleRe: Auto Bed Leveling RC8 - Z axis goes up while homing
The probe you listed is a normally open type, if you conected it to the Z min enstop pins then you need to set this line to true #define Z_MIN_ENDSTOP_INVERTING true // ABL // set to true to invert...
View ArticleRe: Question about using marlin in laser cutting applications
thank you so much, your information was very helpful! regarding modification in plug in , I did as you said, and it seemd logical also to me, but it did not work and still the output does not change....
View ArticleRe: Auto Bed Leveling RC8 - Z axis goes up while homing
Thx that worked! Z axis went up because the probe was triggered when the autohome procedure started.
View ArticleWhen is it necessary to setup multiple "E0 E1 E2" steps and what is the format?
I am using the following setup. RUMBA controller Diamond hot end Marlin 1.1.0-RC-8 Repetier-Host V1.6.2 I have noticed that when I start Repetier-Host the "E" specification is not transferred from the...
View ArticleRe: When is it necessary to setup multiple "E0 E1 E2" steps and what is the...
At a guess you have the eeprom enabled and have not updated that If you use M500 even once then from that point on you must update setting with further M500's. Once the eeprom is used the setting in...
View ArticleRe: When is it necessary to setup multiple "E0 E1 E2" steps and what is the...
Dust Thanks for responding. Well I gave that a try and it did not seem to work. However I changed from Marlin 1.1.0-RC8 to Marlin 1.1.0-RC8 bug fix and it seemed to clear it up. But there seems to be...
View ArticleRe: When is it necessary to setup multiple "E0 E1 E2" steps and what is the...
oh and the subject line... * X, Y, Z, E0 [, E1[, E2[, E3]]] so with 3 extrudes you just add extra prameters #define DEFAULT_AXIS_STEPS_PER_UNIT { 160, 160, 3200, 188.53, 200, 150 }
View ArticleRe: When is it necessary to setup multiple "E0 E1 E2" steps and what is the...
Dust Thank you I don't know why they use E0 [, E1[, E3 etc.... To me it would have been simpler just to state it the way you did or E0, E1, E2.... The [ threw me off. Also it helped me figure the this...
View ArticleRe: When is it necessary to setup multiple "E0 E1 E2" steps and what is the...
For what it's worth: I found that my moving the power plugs for the steppers to "E0" one at a time I was able to calibrate the 3 steppers used by the Diamond hot end. It should be mentioned that I...
View ArticleRe: When is it necessary to setup multiple "E0 E1 E2" steps and what is the...
Different idle pressures can change your steps/mm as more or less filament goes deeper or lighter into the extruder gear
View ArticleError uploading new Marlin
Hi, I'm new in all 3D printing world... trying to configure and upload the Marlin FW and getting error message about this line (in boards.h): #define MB(board) (MOTHERBOARD==BOARD_RAMPS_14_EEB ) What...
View ArticleSetting Marlin for LCD problem
Hi guys! I open the topic here because I really think I have a problem with setting Marlin in order to have a functional LCD. So, I have a 2004 LCD 20x4 [www.aliexpress.com]. You can check in the link...
View Article