Re: Desperate
This sounds like a dead mosfets, but I am suspicious of your firmware, if the pins are wrong... It could act the same. what controller does it comes with and what motherboard type did you set in...
View ArticleRe: mintemp triggered heater_id:0
double check the wiring ? which changes did you make in firmware ?
View ArticleRe: mintemp triggered heater_id:0
and what temperature does the hot end read at room temp? I suspect new thermistor on hotend is not connected correctly.
View ArticleBack off endstops after homing
Hi, is there a way to configure marlin to back off the endstops by about ~5mm after homing (all axis)? I'm used to repetier and it has this feature but I couldn't find it on marlin... Thx :)
View ArticleOnly allowed K numbers 0 - 10 at Linear Advance
I tried to start using Linear Advance in the new Marling. I calibrate everything and tried in the firmware code to set K to 40. When I then compile in Arduino IDE I get this message: LIN_ADVANCE_K...
View ArticleRe: Linear Advance questions
The linear advance calculation changed in Marlin 1.1.9 (from linear advance 1.0 to 1.5) and the units changed along with it. So you will need to calibrate for a new K factor value if you just updated...
View ArticleRe: Linear Advance questions
Everywhere you read about calibrate the K value the talk about 40, 50, 60 and so on. But if I try to use this I got the error message. All tools give this type of values. Where can I find tools I can...
View ArticleRe: Linear Advance questions
Again, that's because they are talking about version 1.0 and you are on version 1.5. Read the marlin wiki for linear advance, and use this to generate test pattern: [marlinfw.org] PAY ATTENTION to the...
View Articlemove Z - axis beyond zero without LCD
hi , i equipped this week my P802MA (melzi board) with a BLtouch probe. For this i have choose a pin i use normally for the LCD and buttons because there is no other pin left. Bltouch works fine and...
View ArticleRe: Linear Advance questions
OK :-) Thank you for replay and link. I'm going to try the test pattern. Yesterday evening I ,(my wife complained) configered the files Configuration.h, Configuration_adv.h who came with 1.1.9....
View ArticleRe: Linear Advance questions
Sorry but there was some problems with the emoji. Please erase this.
View ArticleRe: Linear Advance questions
Yes it can be difficult converting Configuration between versions of Marlin. I always use a diff/merge tool such as WinMerge (Windows) or Meld (cross platform) to make sure all the settings get moved...
View ArticleRe: Can not get firmware working for Wanhao Duplicator i3 with RAMPS1.4 and...
QuoteDust Don't use Arduino: 1.8.6, its very broken use Arduino: 1.8.5, Its known to work. (Arduino: 1.8.7 is also out but untested) Can confirm 1.8.6 was a problem for me too. 1.8.7 worked fine...
View ArticleRe: Linear Advance questions
Quotepeepsalot Yes it can be difficult converting Configuration between versions of Marlin. I always use a diff/merge tool such as WinMerge (Windows) or Meld (cross platform) to make sure all the...
View ArticleRe: mintemp triggered heater_id:0
Thank you. I had a couple of wires plugged into the wrong pin in that "spider web" of wires. It seems to be working now. :)
View ArticleRe: mintemp triggered heater_id:0
Thank you. The hot end was registering the same as the room temp. I had a couple of wires plugged into the wrong pin in that "spider web" of wires. It seems to be working now. :)
View ArticleMarlin 3d Printer Tool question..
Is anyone familiar with using the "marlin 3d printer tool" ? in the marlin tool, when i go to do the Z-Maintenance, it shows my maximum Z travel as 300mm, when i believe on the tevo tornado, it should...
View ArticleRe: Marlin 3d Printer Tool question..
Go to Github Link and post your question there, you would get the best answers there
View ArticleDuet Wifi over extrusion on later change with Slic3r
Hi all I recently upgraded to a Duet Wifi board for my core xy printer. I’m running Slic3r 1.2.9 and firmware 1.19 on the duet. At a later change the printer does a large retract followed by an over...
View ArticleRe: Duet Wifi over extrusion on later change with Slic3r
Not trying to be rude or anything - but had you thought about posting this in the Duet area, rather than the Marlin firmware one? ( Home > Electronics Folder > Duet )
View Article