1.1.x_bugfix Leveling issues
Hi- I am having trouble with bilinear bed leveling with the 1.1.x bugfix release. I can not determine if its the sensor being flakey or if its the firmware. Here is a video of Autohoming and G29...
View ArticleRe: Extruder stutters and doesn't turn
What are your steps/mm for the extruder in the configuration file? Are you taking into consideration the changes in native usteps? Double checked your electrical connections? What about wiring? Are...
View ArticleRe: 1.1.x_bugfix Leveling issues
You mesh points are very large. This implies you do not have your Z_PROBE_OFFSET_FROM_EXTRUDER set correctly. You mesh point values should be centered around 0.00 mm.
View ArticleRe: 1.1.x_bugfix Leveling issues
thanks for the reply. maybe i was not specific enough- yes, i understand that i should be somewhere around 0 for the mesh points. this is how things were looking when i first got the probe. my Z probe...
View ArticleConnecting 2 E mottors
Hello! I have CTC dual with MIghtyboard electronics and changed firmware to Marlin (attached to post). I would like to control both E motors simultaneously, as one motor. I tried to use mixing...
View ArticleInvert Logic of any Digital Pin used for Fans and Lights
Hi Folks, I did some smaller mistake in my Hardware "design" as I soldered a small Board to switch Fans and Lights With D47 D45 D43 and D41 The Board Works as expected but Digital HIGH turns the light...
View ArticleRe: Need help configuring extruder_fan & part_cooling_fan
And Where is your part cooling Fan connected to? it looks like you have your Partcooling fan also on Pin 8. this is not allowed, and would make no sense, because Partcooling would be always on With...
View ArticleRe: 1.1.x_bugfix Leveling issues
There have been some changes to the probing code over the last 2 weeks in response to issues of probing on the edge of the bed. It is very possible the lastest code addresses some of what you are...
View ArticleRe: 1.1.x_bugfix Leveling issues
This WAS with the current code, bugfix from 5/26/2018. What should I be using instead?
View ArticleRe: Need help configuring extruder_fan & part_cooling_fan
Hi kabelfrikkler, I have attached a photo from rambo board. I have my extruder's heater block connected to "heat 0". The extruder's fan is connected to "fan 0" and this is pin 8. The part cooling fans...
View ArticleRe: 1.1.x_bugfix Leveling issues
That code is a week old. And changes have been made to it. If the changes don't fix your issue, please start a thread at [github.com] and we will get the right people focused on it.
View ArticleBLTocuch 3D on Marlin 1.1.8 and other issues
Hi everybody I built my own 3d printer and I am using marlin 1.1.8 firmware. I cannot put BL Touch 3D working, as well as endstops. Also I got error when triyng to warmup bed to 110º to print with...
View ArticleClik here to view.
How to remove marlin logo on reprap discount lcd
Hi guys can anyone please tell me how can i remove or change the marlin logo on splash screen / boot screen on reprap discount lcd. ibb.co how to delete twitter account permanently
View ArticleRe: How to remove marlin logo on reprap discount lcd
There are many articles of how to change the Marlin start up Screen or Custom Boot Screen for Marlin. try the two links below. [community.robo3d.com] [www.youtube.com] Still need help post again
View ArticleRe: How to remove marlin logo on reprap discount lcd
QuoteRoberts_Clif There are many articles of how to change the Marlin start up Screen or Custom Boot Screen for Marlin. try the two links below. [community.robo3d.com] [www.youtube.com] Still need...
View ArticleRe: How to remove marlin logo on reprap discount lcd
This RepRapDiscount Smart Controller contains a SD-Card reader, a rotary encoder and a 20 Character x 4 Line LCD display. Boot Screen Message in RED To remove it use "//" //#define SHOW_BOOTSCREEN To...
View ArticleRe: How to remove marlin logo on reprap discount lcd
The 20x4 LCD Displays allow 'custom characters' to be defined. The corners of the box are customer characters. Marlin also uses custom characters with the UBL Mesh Edit from the LCD Panel. It uses...
View ArticleRe: How to remove marlin logo on reprap discount lcd
"But why would you want to hide the fact you are running Marlin firmware?" Obviously trying t hide their blatant GPL violations....
View ArticleTEMP SENSOR CHAMBER
While running through a configuration.h file the other day on this 3D forum, spotted the following line of code. #define TEMP_SENSOR_CHAMBER 0 It however it had no other supporting information with...
View ArticleRe: TEMP SENSOR CHAMBER
OK, found that Marlin 2.0.X has "#define TEMP_SENSOR_CHAMBER 0" included However do not know much about this Version " Can this be upload this onto a Ramps 1.3/1.4 compatible controller, that was...
View Article