Re: Continue printing after power off and power the 3D Printer on again
Quotehadi I don't want to use UPS or extra battery. You can dictate what you want the solution to be... But you may not get an answer.
View ArticleRe: Continue printing after power off and power the 3D Printer on again
Must be a Pointy-haired Boss type ... "Do it this way, don't care that's its impossible" 1) sd cards have a limited number of write cycles, updating it constantly with a pointer to g code location and...
View ArticleRe: Continue printing after power off and power the 3D Printer on again
Thanks for all of that description, then I have to edit the power supply at first. Do you know how to edit the it ? what shall I add to it ? and when the controller receives the signal from the power...
View ArticleRe: Continue printing after power off and power the 3D Printer on again
Is the relay good for that function ?
View ArticleRe: Continue printing after power off and power the 3D Printer on again
So I have to copy the filament run out sensor commands from (SERVO3_PIN) to (SERVO2_PIN) to sense the relay signal and write M190 S0 , M104 S0 and M18 (to save the remaining power) then eeprom the...
View Articlebed and nozzle temperatures
MKS genv1.4 with TFT32. single head. Both the bed and head temperature show as the same on the TFT32. Which ever one rises it shows the highest temperature. 100K on bed. no pull up. 100k glass bead on...
View ArticleRe: X axis too fast when starting print.
update. fitted new stepper motors. working properly.
View ArticleCant get marlin to compile, "collect2.exe: error: ld returned 1 exit status"
I've been using SkyNet3D-V2.3.2 and was having a bed leveling problem where all of the auto leveling options had a leveling error ( the same slant, in the same direction, ruled out mechanical error)...
View ArticleRe: Marlin 1.1.5
At this point I have re-flashed Marlin 1.1.5 too many times to count, and have made only minuscule changes, and had but forgotten about this problem. Until I ran across this line of code " #define...
View Articleheat bed stops the print
Hi All. i have this problem with my delta printer i just finish hope someone can help me. i am using marlin 1.1.4 when i slice a model with no heated bed it prints ok with PLA 210 hot end ( with the...
View ArticleRe: heat bed stops the print
a few things to look at... check your thermistor wireing and values in your Configuration.h file. The wrong thermistor compared to table is possible. Both your settings are = 1 : 100k thermistor -...
View ArticleThird independent thermistor? [Marlin / RAMPS / Repetier]
Hi all! I have had some breakdowns (heat-creep most probably) in my E3D v6 bowden, and it's probably one or several of these reasons: too much retraction, too slow print, old filament and bad cooling...
View ArticleRe: heat bed stops the print
Hi. thanks for your help. i change to PIDTEMPBED and run the test to get the values to store in the firmware. but no luck. i also change the BED_MAXTEMP to 110 i will check the wiering, question. if...
View ArticleRe: heat bed stops the print
ya I would say that is likely, so with that much free air blowing down the bed cant keep itself hot enough. the heater stays on all the time trying to compensate thus tricking the system to think its...
View ArticleRe: Third independent thermistor? [Marlin / RAMPS / Repetier]
A common problem with the clone e3d v5 and v6 is the fans supplied are not acceptable. You need at least 5cfm of air on that little 30mm fan to make the heat brake do its job. Get a high RPM BB 30mm...
View ArticleRe: Third independent thermistor? [Marlin / RAMPS / Repetier]
Hey I just saw this and thought of your issue.... [www.youtube.com] instead of a loud fan on the heatbrake how about water cooled!!
View ArticleRe: heat bed stops the print
Hi. i got it working, it was way to much air from the 2 fans, i think that even the hot end fan helps in small pieces, i print a calibration cube 25 x 25 x 10mm and as soon as the fans kick in in the...
View ArticleRe: where is Z max?
I just ran into that tonight. My Z min works for homing, but the Z max end stop is not seen. I have RAMPS 1.4. I can't find where Z_STOP_PIN is defined. This looks like we only get either Z_MIN_PIN or...
View ArticleRe: Third independent thermistor? [Marlin / RAMPS / Repetier]
Hey thanks! I actually have exactly that fan in the thingiverse picture (Noctua 40x40)! It does 5.88cfm IIRC but I guess it's hampered by my ugly attachment, this one looks much better. I put back the...
View Article