RC-8 issues
I tried to download the new RC and just using the stock version from the github page I cannot verify it out of the gate. It gives me this message: Arduino: 1.6.13 (Windows 10), Board: "Arduino/Genuino...
View ArticleRe: Z-probe configuration in Configuration.h
Got an answer at the Marlin git repository. Use the Z-Sled probe and comment out the sled moves in Marlin_Main.cpp and the sanity check preventing use with delta printers in SanityCheck.h.
View ArticleAfter setting up auto bed leveling, printer loses reference to home
Hi, I have a Folgertech i3 2020, running a ramps 1.4 and Marlin 1.0.2 firmware. I installed a inductive sensor for bed leveling and went through the setup on that and got the probing working fine....
View ArticleRe: After setting up auto bed leveling, printer loses reference to home
Do you still have the X endstop on the right (max) side of the printer as default from Folger? If you do I don't think auto leveling will work properly. Check out [folgertech.wikia.com] for more...
View ArticleRe: After setting up auto bed leveling, printer loses reference to home
QuoteDaveA Do you still have the X endstop on the right (max) side of the printer as default from Folger? If you do I don't think auto leveling will work properly. Check out [folgertech.wikia.com] for...
View ArticleNeed some help with steps/mm
I'm running Marlin 1.1.0 RC7 on my newly minted D-Bot Core XY and I have some issues with the steps/mm settings. I'm using the DRV8825 drivers with the MS3 jumper set which essentially means they are...
View ArticleRe: Need some help with steps/mm
Your math looks right I would guess you have and eeprom enabled and you updated your configuration.h with the new steps/mm values The eeprom takes precedence over the configuration.h Send a M503 and...
View ArticleRe: Need some help with steps/mm
Right! M503 shows the same values as configration.h. Though this is still a mystery, I changed the value to 400 from 1600 and now the travel is correct. I can't figure out the math though!
View ArticleRe: Need some help with steps/mm
Are you sure that your microstepping jumpers are set correctly?
View ArticleRe: Need some help with steps/mm
Are you sure of these are 2mm pitch acme leadscrew, url to source? If they are multi start vs single start then that changes things, take a look at them end on.. single start you can only see one...
View ArticleZ axis will not respond to homing command (Mendel90)
I'm having an issue with running G28 commands on my Mendel90. Sending G28 homes the X and Y axis but Z axis does not move at all. Sending G28Z also has no response from the printer. Sending G0Z...
View ArticleRe: Z axis will not respond to homing command (Mendel90)
what about Homing speeds, which you have conveniently not shown The defaults are // Homing speeds (mm/m) #define HOMING_FEEDRATE_XY (50*60) #define HOMING_FEEDRATE_Z (4*60) Ie the last one should be 2*60
View ArticleAuto bed level unstable
Is there a reason I have to keep changing the Z-offset for auto bed leveling? Having given up totally on my Delta printer, I thought that since I had the sensor, I might as well install it on my...
View ArticleAzteeg and Viki2 with RC8
I have a stable working RC7. This weekI have tried to update to RC8 and RCBugFix. When i click the encoder on the viki2 controller I get a crash- Killed. message on the LCD. Can anyone else with an...
View ArticleRe: Auto bed level unstable
Your endstops are 'moving'. Losing steps on the motors. Loose screw on one or more pulleys. For the ir sensor, bed surface not reflecting ir consistently. Tilting of the effector.
View ArticleRe: Auto bed level unstable
If your firmware supports it try building with Z_MIN_PROBE_REPEATABILITY_TEST enabled. Load it and then do a G28 followed by an M48 to run the repeatability test. I'm using RC8BugFix, a BLTouch...
View ArticleRe: Auto bed level unstable
Ive always had issues with auto level and offset with every print. I just ran the probe repeat and got this: SENDING:M48 P4 X100 Y100 V4 M48 Z-Probe Repeatability Test Positioning the probe... Bed X:...
View ArticleMarlin PID temperature control code isolation
Hello all reprapers! I'm currently working on a project where I need to control the temperature of a metal block using a 40w cartridge heater and 100k thermistor. at the moment I am using an arduino...
View ArticleRe: Auto bed level unstable
Quotestephenrc Your endstops are 'moving'. Losing steps on the motors. Loose screw on one or more pulleys. For the ir sensor, bed surface not reflecting ir consistently. Tilting of the effector. End...
View Article
