Fabrikator Mini 1.5 with Marlin 1.1.0-RCBugFix Extruder Problem
Hello, I updated my new Fabrikator Mini 1.5 to Marlin 1.1.0-RCBugFix. Unfortunately all prints are failing with too less filament. Are this the extruder steps? I tried to change the settings from...
View ArticleMarlin 2004 LCD Smart Display Controller Module Issues
I am trying to use a 2004 LCD Smart Display Controller Module (Amazon) as an interface for my GT2560 board. Sadly though I am experiencing quite the difficulty setting up what looked like the easiest...
View ArticleRe: Marlin 2004 LCD Smart Display Controller Module Issues
If it is from Geeetech, it sucks. Have you tried asking them how to do it? I don't quite remember, but isn't the GT2560 board an inferior clone of the Mega2560 board? If so, we can probably figure out...
View ArticleRe: Fabrikator Mini 1.5 with Marlin 1.1.0-RCBugFix Extruder Problem
You really should do a M502 and a M500 any time you change the Configuration.h file. Otherwise, you are still going to pick up 'old' settings out of the EEPROM.
View ArticleClik here to view.
Re: Marlin 2004 LCD Smart Display Controller Module Issues
It is ULTIMAKER compatible so #define MOTHERBOARD BOARD_ULTIMAKER is correct There are two different wiring for LCD's If the pin on the back of the LCD are bent like this the cables are 180 degrees...
View ArticleRe: Marlin 2004 LCD Smart Display Controller Module Issues
I took some jumper wires and flipped all the connections upside down (the way the connector will not plug in) and it worked -.- [attachment 85042 IMG_20161017_230231.jpg] That is headache inducing......
View ArticleRe: Marlin 2004 LCD Smart Display Controller Module Issues
yay for getting it going And a big thanks has to go out to China, causing nightmare inducing headaches for everyone (for a bargain price.)
View ArticleHome hotend on Print Stop
Ladies and gents, Probably I could have done more googling but well... I do have a end.gcode set in my slicer so when print finishes it homes XY and drops Z down but that obviously only works if print...
View ArticleWrong Thermistor or what?
My k8200 is running marlin and my board shows me wrong temps (http://puu.sh/rNcbP/3df1c0b49e.png), the room temp when this screen was created is 22,1°C. Can I fix this issue with a Firmware update?...
View ArticleRe: Marlin 2004 LCD Smart Display Controller Module Issues
Quotekylepls I took some jumper wires and flipped all the connections upside down (the way the connector will not plug in) and it worked -.- [attachment 85042 IMG_20161017_230231.jpg] That is headache...
View ArticleRe: Self made delta printer homing problem
The problem is fixed!! What happend was that I forgot to set the jumpers underneath the motor drivers. Because of this the motor steps where way to big. In the homing sequence the motor move up until...
View ArticleRe: Fabrikator Mini 1.5 with Marlin 1.1.0-RCBugFix Extruder Problem
Just saw that I was on the RC branch and not on the latest RcBugFix Branch. Updating to RcBugFix and reset to factory settings helped. Now the print looks good.
View ArticleRe: Adding jog buttons to use with auto torch height controller
If you use RCBugFix, you will find a lot of people willing to jump in and help you. A lot of the developers are forward looking, and don't want to mess around with an older code base. With that...
View ArticleHeating failed ID: Bed. Unable to find a solution
Hi reprap peoples, Decided to get involved in the reprap scene and build a 3d printer, got everything going mostly sweet minus the MK2A heated pcb bed (200x200) which i can not just seem to get to...
View ArticleRe: Heating failed ID: Bed. Unable to find a solution
Put a multimeter into both pins of D8, turn on the bed in software, do you get 12v? Also try the heated bed with the bed +12v plugged into D8 + but the gnd directly to gnd on the power supply.. This...
View ArticleWhen move axis with rotary encoder just after 3 seconds the 3d printer do...
When i go to menu move axis and try to move one of the axis just after 3, 2 seconds the printer actually start working ... why ? and how can i do fix this ?
View ArticleRe: Heating failed ID: Bed. Unable to find a solution
I just cringed, some times the obvious is the first thing you miss, will hang my head in shame and confirm tomorrow arvo that i am in fact a idiot when i wire in the second 12v + gnd cable many thanks...
View ArticleRe: Self made delta printer homing problem
Good you made a FIX... Could I please have a copy of your configuration.h ? I am working on my own 3D-printer: [www.planker.dk] Thanks...
View ArticleIs it possible...
I recently got my E3D Legendary pack and setup the Marlin firmware for dual extrusion and installed the Chimera hardware. everything went well and I am dual extruding with different materials and...
View Article