Re: Is it possible to allow homing of Z axis only with hot nozzle?
the bltouch has a extendable probe that is reasonably long... It sounds like you need to move you bltouch lower so that the probe extend much lower that the nozzle, not just a mm or so.
View ArticleRe: Is it possible to allow homing of Z axis only with hot nozzle?
That's a good point, thanks. But nevertheless this could happen in an unlucky situation.
View ArticleMarlin 2.0.5.3 won't home properly
I bought an SKR v1.3 board a while ago and I got some time now to upgrade my printer. I bought the TMC2208 drivers with it. I am able to get most of the configuration working except for homing. I have...
View ArticleMore decimal on lcd display for step
Hello everyone, I'm a beginner on Marlin firmware, I finally received my skr e3 motherboard on an ender 3,an I have a problem to the step. I can enter the steps / mm only at one digits (80,x) before...
View ArticleRe: More decimal on lcd display for step
... if it helps, here is the French sub-forum - [reprap.org]
View ArticleRe: linear advance settings
Can you tell me the relationship between acceleration and linear advance? If I increase acceleration how does that affect LA? I have the same question for Ejerk. I've seen some posts that say LA and s...
View ArticleMarlin 2.0.5.3 Viki2 Blank Display
Hello Everyone, I am having issues getting an Airwolf Axiom upgraded to Marlin 2.0. I have everything configured and working, including steppers, homing, thermistors and heaters, but the LCD screen, a...
View ArticleRe: linear advance settings
In general, the higher the acceleration the more LA needs to compensate.
View ArticleMariln firmware issue
I have been building a RAMP 1.6 system using Marlin 1.1.x-bugfix (which is 1.1.9 I believe) in an old 3D printer that had it's proprietary control board blow. For a while I've been trying to get it to...
View ArticleClik here to view.
Re: linear advance settings
I'm looking for a way to test different settings but I'm not sure what to test for. The tests I've been doing just confuse instead of clarify. If I tested different accelerations I could probably get...
View Articlemoving from bug-fix build to release build
I have been running the bug-fix source of Marlin for quite a while and decided to move over to the release version instead. I figured I should be able to just copy my 2 config files and the...
View ArticleRe: Mariln firmware issue
I upgraded to the latest FW available, 2.0.5.x and the behavior has changed. Now layers 1-3 print fine and 4-10 are slightly offset but to only a minor degree. I printed 3 of the same on the same...
View ArticleOrigin position in Marlin
Good evening, I have some troubles understanding the position of he origin in Marlin. What is the difference between X_MIN_POS and MANUAL_X_HOME in configuration.h ? Let's say I have an endstop in the...
View ArticleRe: Warning in marlin bugfix-2.0.x Build
did you eever find out the cause or solution for this? I am having the same error message.
View ArticleCan't get Marlin 2.0 to work with my MKS SGEN L
Hi everyone ! Recently, I've ordered one of thoses MKS SGEN L board, with 5 TMC2209 V2 from MKS. When I received it, I downloaded the Marlin Bugfix Branch, I configured it and compiled it. No error,...
View ArticleRe: Can't get Marlin 2.0 to work with my MKS SGEN L
There are apparently issues with bugfix and your board. use stable
View ArticleRe: Can't get Marlin 2.0 to work with my MKS SGEN L
Okay, so i tried to boot up with the latest stable marlin version (2.0.5.3) with the same configuration as before, but... Nothing. i can't connect it to my computer, even with my MKS TFT 28... I'm...
View ArticleRe: Origin position in Marlin
In almost all cases there's no difference - it only really comes into play when you have multiple independent extruders. I prefer to use X_MIN_POS/Y_MIN_POS since it makes more sense to my brain.
View Article3D printer Help Needed please!!!
I have a FLSUN extended bed printer I bought a few years back similar to the one in this link...
View ArticleRe: 3D printer Help Needed please!!!
... check for loose/broken cables or temp. sensor ...
View Article