Feature Request Consideration - Relay Operability Check & Relay Failsafe...
Hey dev team! I think of this as a "relay failsafe runaway protection" to prevent unregulated current to designated circuitry. It would require logic to be developed and some minor circuit addition....
View Article2.0.4 - Aggravating Print Issue
Printer: Anet A8 Marlin 2.0.4 Prusa Slicer Repetier Host ----------------- Upgraded to an SKR 1.2 E3 just for performance increase and noise reduction. I have ran out of ideas on how to fix my print...
View ArticleRe: Feature Request Consideration - Relay Operability Check & Relay Failsafe...
Not exactly what you're asking, but you might want to take a look at SUICIDE_PIN. This is a pin that gets switched whenever a kill condition occurs - for example in case of a thermal runaway. You...
View ArticleRe: 2.0.4 - Aggravating Print Issue
Quote1000Calories Took a peak at the gcode for the calibration cube file in Repetier, and saw the beginning coordinates for the print. It's way out of range but the placement of it never affected my...
View ArticleRe: BTT SKR 1.4 ignoring Endstops
Quotemodsolution Did you try this... [marlinfw.org] That did the trick. Now the Stepper Motors make weird noises before homing, but that's another issue. At least they are homing now. Thank you!
View ArticleRe: BTT SKR 1.4 ignoring Endstops
Sounds like you are not getting enough power to your driers. Do a search for... #if HAS_TRINAMIC and adjust your RMS current there. And you are welcome glad I could help!!
View ArticleRe: Feature Request Consideration - Relay Operability Check & Relay Failsafe...
That is totally new to me. I thought I'd looked into everything safety related. That is indeed very similar and could be utilized to a similar end. Thanks!
View ArticleRe: Marlin 2.0.4: Bed Heating Failure
No! Was merely stating that I started using Marlin 2 alpha when doing the conversion. Asking if you would compare the settings again from Marlin 1.1.8 to Marlin 2.0.x using a different type method...
View ArticleRe: BTT SKR 1.4 ignoring Endstops
Thought so too, but there was actually just a wire from the stepper motor coming lose after all the troubleshooting. re-crimped it and now everything works fine. Thanks again though!
View ArticleRe: 2.0.4 - Aggravating Print Issue
Not sure if software end stops would effect that? I have to check but not sure if it is disabled.
View ArticleRe: Printer won't connect via USB with some firmware options enabled
Finally figured this out. It appears to have been the SD card - this issue here: [github.com]
View ArticleM420 S1 Z10 crashing marlin
I've been trying to get mesh bed leveling working on my printer and have run into a problem. Every time I send M420 S1 Z10 to the printer the lcd goes blank and the printer resets. I've tried running...
View ArticleHow can I calculate the actual pritable area and set it in Marlin 2 ??
Hi I'm new to this 3D printing hobby so be easy.\ I have generic reprap printer with the X,Y endstop located on the LEFT and BACK of the printer so I asume that the 0/0 position of the printer is...
View ArticleRe: How can I calculate the actual pritable area and set it in Marlin 2 ??
By LEFT/BACK you mean that the X carriage is to the left and the bed is at the back? In this case the home position is actually LEFT/FRONT since you care about the location of the nozzle with respect...
View ArticleMarlin 2.bf - G76 - Probe temp. compensation error
Hey there, I just dug out my Wanhao Duplicator I3 and did a few upgrades including SKR 1.4, TMC 2130 SPI and an inductive Z-probe. It auto levels and prints fine but now I wanted to add temperature...
View ArticleRe: How can I calculate the actual pritable area and set it in Marlin 2 ??
When I press HOME, the bed moves to the left and to the back. Is this normal?
View ArticleRe: How can I calculate the actual pritable area and set it in Marlin 2 ??
Please provide pictures of your machine. The bed on most machines only moves in one direction, Normally front to back or up and down. But there are some oddball machines that move the bed in...
View ArticleRe: How can I calculate the actual pritable area and set it in Marlin 2 ??
Sorry for the misunderstanding, what I meant to say is during the home stage the extruder assembly moves to the left (that is where the endstop is) and the heat bed moves to the back (that is where...
View Article