Re: REPRAP DISCOUNT FULL GRAPHIC SMART CONTROLLER DISPLAY ERROR
Test with short cables. What controller is this on?
View ArticleRe: Prusa clone (anet A8 electronics) marlin issue
#1 in Configuration_adv.h //#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu. Enable this line. #2 in Configuration_adv.h //#define...
View ArticleCompile error
I am using Arduino 1.8.9 and an old 1.1.9 copy (unzipped 2/24/2019) of Marlin. When I try to confirm that the original Marlin file will compile I am getting the following error:...
View ArticleRe: Compile error
... with this "Segmentation fault" error I'm deleting or changing comment lines and try to recompile, until it works -- this error is "sporadic" and I have no clue otherwise 8-)
View ArticleMarlin 2.0 Compile Error
Trying to compile Marlin 2.0 for an SKR Mini E3. Every time I try to compile any fork of Marlin 2.0 I get a failure. I think it is missing something that python needs but I cannot figure it out. I...
View ArticleRe: Compile error
Delete the Arduino IDE app, its is broken. use the installer or the zip version Windows Installer Windows ZIP file for non admin install
View ArticleRe: REPRAP DISCOUNT FULL GRAPHIC SMART CONTROLLER DISPLAY ERROR
I'm already using short cables, I'm using Marlin 1.1.9 with ramps.
View ArticleRe: REPRAP DISCOUNT FULL GRAPHIC SMART CONTROLLER DISPLAY ERROR
Try the GLCD tester [github.com] What are those cables, they don't look like normal ribbon cables.
View ArticleRe: Compile error
... I have the same error with different ZIP-IDE's on two different PC's - so it seems to be a more complex cause :S
View ArticleRe: Prusa clone (anet A8 electronics) marlin issue
Thank you very much Dust, can’t wait to test this next week. The only question I have without trying it is, QuoteDust // Add M701/M702 Load/Unload G-codes Will I add the gcode I have in the place of...
View ArticleRe: moved from ancient Marlin to Marlin 1.1.8, now hotend does not heat up
While I am guessing this is not the cause, I thought I would offer the following as I had something similar happen to me (printer worked and then after some work on the board and flashing, the end...
View ArticleRe: REPRAP DISCOUNT FULL GRAPHIC SMART CONTROLLER DISPLAY ERROR
QuoteDust Try the GLCD tester [github.com] What are those cables, they don't look like normal ribbon cables. They look wrapped in aluminium foil. Are you sure there are no shorted pins?
View ArticleMarlin 2.0.x Z axis not homing to MAX endstop with G28 etc
HI Everyone, Im setting up a new printer with Marlin 2.0.x on a Azteeg X5 GT from Panucatt and 32bit Im having a problem with Z homing to max endstop. What ive found so far: Physical endstop is...
View ArticleRe: REPRAP DISCOUNT FULL GRAPHIC SMART CONTROLLER DISPLAY ERROR
QuoteOhmarinus They look wrapped in aluminium foil. That is my guess also, which you would normally only try if you where trying to sheid overly long cables... Which is why I said to use short cables...
View ArticleRe: Marlin 2.0.x Z axis not homing to MAX endstop with G28 etc
What happens when you set: #define Z_HOME_DIR -1 Assuming you are using an Hbot or corexy. The bed still homes to Zmin btw. It just moves up instead of down. If the bed moves to zmax it means the bed...
View ArticleRe: Marlin 2.0.x Z axis not homing to MAX endstop with G28 etc
Yes Concurr, Just came to the same conclusion and BOOM works well. Thanks for your help. jas
View ArticleRe: Marlin 2.0.x Z axis not homing to MAX endstop with G28 etc
QuoteJasontwd Yes Concurr, Just came to the same conclusion and BOOM works well. Thanks for your help. jas Ah good to hear! Any place where we can see your printer? :)
View ArticleFinal Marlin configuration
Been a long road but my FLSUN kossel is almost ready to print again. I have everything set using the manual configuration process to modify the Marlin script using Arduino. However, now I have all the...
View ArticleDelta homing under Marlin - moved from 'Deltas'
I moved this problem from 'Deltas' to here are it's more of a Marlin issue than specifically with the machine itself. I have a fairly new Anycubic Kossel Linear Plus running Marlin 1.1.9 (recently...
View ArticleRe: Marlin 2.0.x Z axis not homing to MAX endstop with G28 etc
Thanks, I 've set up a blog, but havnt put any new stuff on there for ages. I'll get some writing and info up there and send you link once ready eh. You got messanger address and I flick you some...
View Article