home no longer goes to center of bed and z safe homing now creates error
After Updating my marlin to bugfix 2.0 My Cube no longer homes to the center of the bed.I had all the pertinent setting that I have tweaked for my machine saved so I only changed those settings. I...
View ArticleRe: Issue with Marlin and reprap display
If your SSD1309 uses I2C communication, this thread using SSD1306 (which seems to be compatible with SSD1309) might be helpful.
View ArticleRe: Issue with Marlin and reprap display
This is the one I'm using [www.crystalfontz.com] In the datasheet for the chip it says this Pin selectable MCU Interfaces: o 8-bit 6800/8080-series parallel interface o 3 /4 wire Serial Peripheral...
View ArticleHow Do I Enable the M140 Heating Bed Option?
I am using Marlin 1.1.9. I am trying to heat my bad using the 'M140 S60' command but it's not working. When I enter this in Pronterface I get: Setting bed temperature to 60.000000 degrees Celsius....
View ArticleRe: How Do I Enable the M140 Heating Bed Option?
HAS_HEATED_BED has to be defined this is true when HAS_TEMP_BED && HAS_HEATER_BED is defined HAS_TEMP_BED is true when HAS_TEMP_ADC_BED HAS_HEATER_BED is true is PIN_EXISTS(HEATER_BED) So...
View ArticleRe: Issue with Marlin and reprap display
Did you see that the documentation says that this OLED is for "3.3Volts only"? Do you have a printer controller board which generates 3.3V signals? Or have you found in the documentation something...
View ArticleRe: Z home pronterface works, G28 Z0 makes Z movement freeze
Well, I've pretty much given up. I hate this. I've tried a gazillion Marlin settings and today I even replaced the TMC 2130 drivers with basic A4988 drivers. Wrote a fresh new Marlin, uploaded, it all...
View ArticleRe: Z home pronterface works, G28 Z0 makes Z movement freeze
Try sending a M119 - End Stop States It appears that the Z-Axis Sensor is staying triggered, check this using a metal putty knife and the M119 -End Stop States using pronterface .
View ArticleRe: How Do I Enable the M140 Heating Bed Option?
QuoteDust HAS_HEATED_BED has to be defined this is true when HAS_TEMP_BED && HAS_HEATER_BED is defined HAS_TEMP_BED is true when HAS_TEMP_ADC_BED HAS_HEATER_BED is true is...
View ArticleRe: How Do I Enable the M140 Heating Bed Option?
Quotechiques QuoteDust HAS_HEATED_BED has to be defined this is true when HAS_TEMP_BED && HAS_HEATER_BED is defined HAS_TEMP_BED is true when HAS_TEMP_ADC_BED HAS_HEATER_BED is true is...
View ArticleRe: home no longer goes to center of bed and z safe homing now creates error
figured it out, Had bed center at 0 0 should have set it to 130 130, everthing compiled fine once i set that properly
View ArticleRe: Z home pronterface works, G28 Z0 makes Z movement freeze
Thanks for the reply. I checked all with M119 and all homing sensors say open and triggered when they should. But just to be sure, I am hooking up a mechanical end switch (identical to the X and Y...
View ArticleRe: Z home pronterface works, G28 Z0 makes Z movement freeze
Well, I don't get it but I am relatively happy. I replaced the inductive sensor with a micrco-switch, like the switches I have on the X and Y axis. Used all in Marlin with pullups and inverted and it...
View ArticleRe: Einsy + BLTouch? compilation issues..
Did you figure it out? I'm installing my Einsy and came across the same issue
View ArticleMarlin G38.2 dont move Z
Good Evening and nice Christmas :), i have a question. I have a CNC Mill running with Marlin and OctoPrint over Raspbian. Everything is working fine but i did get the G38 command not working. The...
View ArticleRe: Marlin G38.2 dont move Z
Hello :) i dont understand why, but today it is moving the axis but dont stop on probe contact. I will try Marlin v2 and will hope that it is than working. At the moment i use 1.1.09 Thanks Regards...
View ArticleRe: Marlin G38.2 dont move Z, Z Probe dont working
Hey, i know now that the Z Probe for G38 Isnt working when you define (V.2) #define Z_MIN_PROBE_PIN The only possiblity to change the Z_MIN_PROBE_PIN is in the pins_RAMPS file. Thank you. Perhabs...
View ArticleRe: move Z - axis beyond zero without LCD
weißt du ob die P802MA auch beon P802NA geht bekomme bltouch nicht zum laufen kannst du mir deine datei senden zum versuchen danke
View ArticleRe: Marlin 1.1.8 Heating failed error
QuoteGaz83 Cheers Sacramento I will give it ago tonight Did this fix your problem?
View ArticleBLTouch - Marlin 1.0.0 RC2
Hi all, I've been looking for help on this for a while and haven't gotten anywhere with it (including other posts in the wrong location on this forum). I have a Leapfrog Creatr (original) with their...
View Article