Re: Latest stable version of Marlin?
Use Bugfix 2.0.0 as a first attempt. That will be the main branch going forward. It should compile every option you specify for AVR's. Some of the 32-bit platforms still need some work to compile. If...
View ArticleRe: HELP! Endstop problem in Marlin
In config_adv.h there is an option to 'only check endstops while homing' un-comment this // If you want endstops to stay on (by default) even when not homing // enable this option. Override at any...
View ArticleRe: I want to edit SERVO2_PIN function on ramps1.4
It isn't clear to me what behavior you want. Do you want the same servo pulses on both connectors? Do you want the servo connectors used as an input for the filament sensor and you want both of those...
View ArticleRe: I want to edit SERVO2_PIN function on ramps1.4
Actually I'm using filament runout sensor connected to pin (SERVO3_PIN) and I want to add another sensor (to SERVO2_PIN) to sense the power when it turns off, after that I want to change the behavior...
View ArticleRe: I want to edit SERVO2_PIN function on ramps1.4
If this is for a single machine... I'm not sure I'ld even change the name of the pins. I might just make sure the number of servo's is less than 2 so it is safe to use those pins. And then I would put...
View ArticleRe: I want to edit SERVO2_PIN function on ramps1.4
Ok, where to add the extra logic in marlin ?
View ArticleRe: I want to edit SERVO2_PIN function on ramps1.4
Install Astro Grep. Point the directory at the Marlin folder. For the search text, enter: FILAMENT_RUNOUT_SENSOR And press the Search button. You might also want to search for FIL_RUNOUT_PIN These...
View ArticleCustom Bootscreen on Marlin 1.1.6
Hi, is there a possibility to use a custom Bootscreen like i used in Marlin 1.1.4? With the _bottscreen.h? I set up everything like in Marlin 1.1.4 but no Picture appear. THX
View ArticleRe: Custom Bootscreen on Marlin 1.1.6
I figerd it out. I forgot to enable Show_Custom_Bootscreen.
View ArticleRe: Custom Bootscreen on Marlin 1.1.6
Yes... And in fact, there has been some recent work on this topic: [github.com] [github.com] [github.com]
View ArticleNew algorithm
Hi there I saw this new algorithm that reduces the printing time. Would it be possible to use this in Marlin Cheers Scallas
View ArticleRe: Latest Marlin on Printrboard: Problems!
I am new to the forum I dint know where to post this, but wanted some help the potentiometer on my printrboard has worn out and now am not able to adjust the current to my x motor. what is the best...
View ArticleRe: New algorithm
a link to a non pay walled version of the paper, very heavy stuff [www.researchgate.net] Not sure this is needed with modern stepper drivers like the Trinamic2130, the correction part anyways
View ArticleInteraction between T0, T1, and M114
I just installed a dual extruder on my TAZ 6 and was having a problem with the calibration print which led me to perform the following manual experiment. (home, set absolute, auto-level etc.) T0 G92...
View ArticleRe: HELP! Endstop problem in Marlin
Help me obewan, you're my only hope........ Sorry, couldn't resist. Okay, I found the option you mentioned and commented it. I did not find the endstops always on default option, so I added it to the...
View ArticleHow to use AutoBedLeveling for CNC stock surface mapping ?
I use Marlin with a Ramps board to control my CNC machine, its been working great. But, I do a lot of V-carving of signs on edge glued pine boards. The wood is never true and flat. I don't have a...
View ArticleError message: "Marlin\SanityCheck.h:1325:1: error:
I'm trying to compile Marline ver. 1.1.x (1.1.6) and getting some errors. If I change the settings back to the basic 4, it compiles, but with 6 fields I get errors. Error message:...
View ArticleRe: Error message: "Marlin\SanityCheck.h:1325:1: error:
Have you changed #define NUM_AXIS from 4 to 6
View Article