Re: Z axis slams into bed/bltouch offset?/autohome, start print slams
Okay thank you I will try now
View ArticleNozzle touch auto bed leveling
I saw some printer on ali which use nozzle to touch heated bed in order to do autoleveling so I hew few questions How safe is this moving speed while touching bed is very slow ? Is this feature...
View ArticleRe: Nozzle touch auto bed leveling
You need some kind of sensor to sense the touch. Various kinds have been used; a microswitch, electrical, piezo-electric, load-cell. Marlin supports any of these... they just provide a digital on/off...
View ArticleRe: Nozzle touch auto bed leveling
I dont see why sprint and switch and needed Im thinking just using nozzle and aluminum bed as switch, the nozzle is touching the bed so there is your perfect switch its at zero height its not needed...
View ArticleRe: Nozzle touch auto bed leveling
This method relies on measuring the resistance between nozzle and a metal bed... when it's zero, the nozzle is touching. If your printer has a metal structure, the nozzle may already be electrically...
View ArticleRe: Nozzle touch auto bed leveling
heating the hotend and a automated wipe system to clean the nozzle tip is required...
View ArticleClik here to view.
Bedlevelling (all types) is always slightly off.
Hi, Just wondering if I could ask some advice on this : I am using a BLTouch, I have tried - UBL - Linear - Bilinear - 3 point - reverting to 1.1.4 and the results are always variations on a theme :...
View ArticleRe: Z axis slams into bed/bltouch offset?/autohome, start print slams
Thank you how do i turn off the ved leveling? Thanks again i rally appreciate it
View ArticleRe: Nozzle touch auto bed leveling
Quotefrankvdh This method relies on measuring the resistance between nozzle and a metal bed... when it's zero, the nozzle is touching. If your printer has a metal structure, the nozzle may already be...
View ArticleMarlin 1.1 Manual Bed Level Option on Mini Kossel
Hoping someone can assist, I am pulling my hair out with this one. Machine is a Sintron Mini Kossel. Endstops at the top. I am trying to configure the firmware for manual bed levelling from the LCD....
View ArticleRe: Bedlevelling (all types) is always slightly off.
Did you follow the guide at [github.com] to set up UBL? It would be interesting to see your mesh (G29 T) and the G26 Mesh validation test pattern.
View ArticleRe: Marlin 1.1 Manual Bed Level Option on Mini Kossel
Also consider using G33. That is being used successfully by Delta people.
View ArticleRe: Bedlevelling (all types) is always slightly off.
QuoteRoxy Did you follow the guide at [github.com] to set up UBL? It would be interesting to see your mesh (G29 T) and the G26 Mesh validation test pattern. Aye I did. I ended up testing in bilinear...
View ArticleRe: Marlin 1.1 Manual Bed Level Option on Mini Kossel
Hello Wibbles It appears you only need to enable * - MESH_BED_LEVELING * Probe a grid manually * The result is a mesh, suitable for large or uneven beds. (See BILINEAR.) * For machines without a...
View ArticleClik here to view.
Re: Bedlevelling (all types) is always slightly off.
Hi Roxy, Ok so following that guide : 1) The printer should be able to successfully print a small object at the center of the bed with no bed leveling system active. JnUMMPm.jpg Interesting to note,...
View ArticleTurn Hot-End Heater Output Into Always on Fan?
Hello All, I was wondering if it's possible to reconfigure Marlin so that it uses one of my unused Hot-End Heater outputs as an Always on Fan output? It's but of a long story as to why I want to do...
View ArticleClik here to view.
Re: Bedlevelling (all types) is always slightly off.
Quoteglopglop kFZD9Dy.jpg Here the tilt seems to go the other way, so that the "virtual" bed is effectively higher on the left (well front left). It almost feels like the levelling code is...
View Articleend stops
I have upgrade my printer incl firmware ,latest Marlin 1.6,11 Now it's working except the endstops . I have electronic endstops type : opto endstop Before the update it did works . I don't know what...
View ArticleRe: end stops
Not familiar with Marlin 1.6,11 I have Marlin 1.1.5 which is the newest until Marlin 1.2.0 is released also known as Marlin V2.0 you can change the end stops In configuration.h // Mechanical endstop...
View ArticleRe: Manual Mesh Bed Leveling no z endstop
Any new findings about this topic? This topic is on my table now while fine tuning my i3 Rework.
View Article