Re: Z height wrong after z probing

Thanks for your quick response
I attached my two extuder config.

I executed G29 P0 T M A and got that output:

M80
ok
G28
echo:busy: processing
echo:busy: processing
echo:busy: processing
echo:busy: processing
echo:busy: processing
echo:busy: processing
echo:busy: processing
echo:busy: processing
echo:busy: processing
echo:busy: processing
echo:busy: processing
X:200.00 Y:190.00 Z:65.00 E:0.00 Count X: 16000 Y:15200 Z:166400
ok
G29 P0 T M A
Unified Bed Leveling System activated.

Mesh zeroed.

echo:busy: processing
echo:busy: processing
echo:busy: processing
echo:busy: processing
echo:busy: processing
echo:busy: processing
echo:busy: processing
echo:busy: processing
echo:busy: processing
echo:busy: processing
echo:busy: processing
echo:busy: processing
echo:busy: processing
echo:busy: processing
echo:busy: processing
echo:busy: processing
echo:busy: processing
echo:busy: processing
echo:busy: processing
d from first  point: -6.110357  c: -5.440312
d from second point: -6.110357  c: -5.339140
d from third  point: -6.110356  c: -0.987578

Bed Topography Report:

(0,9)                                                                                                                                                             (9,9)
(22,165)                                                                                                                                                         (199,165)
 -5.49565    -4.82179    -4.14793    -3.47406    -2.80020    -2.12633    -1.45247    -0.77861    -0.10474     0.56912   
 
 -5.48170    -4.80783    -4.13397    -3.46010    -2.78624    -2.11238    -1.43851    -0.76465    -0.09078     0.58308   
 
 -5.46774    -4.79387    -4.12001    -3.44615    -2.77228    -2.09842    -1.42455    -0.75069    -0.07683     0.59704   
 
 -5.45378    -4.77992    -4.10605    -3.43219    -2.75832    -2.08446    -1.41060    -0.73673    -0.06287     0.61100   
 
 -5.43982    -4.76596    -4.09209    -3.41823    -2.74437    -2.07050    -1.39664    -0.72277    -0.04891     0.62495   
 
 -5.42586    -4.75200    -4.07814    -3.40427    -2.73041    -2.05654    -1.38268    -0.70882    -0.03495     0.63891   
 
 -5.41191    -4.73804    -4.06418   [-3.39031]  -2.71645    -2.04259    -1.36872    -0.69486    -0.02099     0.65287   
 
 -5.39795    -4.72408    -4.05022    -3.37636    -2.70249    -2.02863    -1.35476    -0.68090    -0.00704     0.66683   
 
 -5.38399    -4.71013    -4.03626    -3.36240    -2.68853    -2.01467    -1.34081    -0.66694     0.00692     0.68079   
 
 -5.37003    -4.69617    -4.02230    -3.34844    -2.67458    -2.00071    -1.32685    -0.65298     0.02088     0.69474   
(22,16)                                                                                                                                                             (199,16)
(0,0)                                                                                                                                                                (9,0)
 
ok

To get really extreme corrections I tilted the bed by 6mm.
But a G0 move along the X-axis causes no reactions on the Z-axis