Re: Bed Levelling on RC8 working but not compensating

I am having the same issue all of a sudden...

I actually got it to work on my DIY The Beast (https://www.instagram.com/bywebberen/)
But lately it just ignores the values after the G29 command... I am at a loss as to what has changed. I have been in my conf.h file again and again. Also if i control the printer via repetier host open config it says auto bed leveling:1(in log) but has a 0 in the text box, if I change it to 1 it now says ERROR: Failed To

19:11:26.936 : Cap:AUTOLEVEL:1
19:11:26.936 : Cap:Z_PROBE:1
19:11:26.936 : Cap:LEVELING_DATA:1
19:11:26.936 : Cap:SOFTWARE_POWER:0
19:11:26.936 : Cap:TOGGLE_LIGHTS:0
19:11:26.936 : Cap:CASE_LIGHT_BRIGHTNESS:0
19:11:26.936 : Cap:EMERGENCY_PARSER:0
19:11:26.936 : N11 M221 S100*80
19:11:26.938 : N12 M111 S6*84
19:11:26.938 : X:0.00 Y:0.00 Z:0.00 E:0.00 Count X:0 Y:0 Z:0
19:11:26.938 : echo:DEBUG:INFO,ERRORS
19:11:26.938 : echo:Active Extruder: 0
19:11:26.940 : N13 T0*8
19:11:26.940 : N14 M155 S1*85
19:11:26.961 : echo:DEBUG:INFO,ERRORS
19:11:26.961 : echo:Active Extruder: 0
19:11:56.178 : N15 M503*17
19:11:56.260 : echo: G21 ; Units in mm
19:11:56.260 : echo:Filament settings:
19:11:56.267 : echo: M200 D1.75
19:11:56.272 : echo: M200 T1 D1.75
19:11:56.272 : echo:Steps per unit:
19:11:56.294 : echo: M92 X80.00 Y80.00 Z400.00 E356.00
19:11:56.294 : echo:Maximum feedrates (units/s):
19:11:56.317 : echo: M203 X100.00 Y100.00 Z15.00 E100.00
19:11:56.317 : echo:Maximum Acceleration (units/s2):
19:11:56.335 : echo: M201 X2500 Y2500 Z50 E5000
19:11:56.335 : echo:Acceleration (units/s2): P R T
19:11:56.344 : echo: M204 P8000.00 R8000.00 T3000.00
19:11:56.345 : echo:Advanced: S T B X Z E
19:11:56.371 : echo: M205 S0.00 T0.00 B20000 X25.00 Y25.00 Z0.40 E5.00
19:11:56.372 : echo:Home offset:
19:11:56.386 : echo: M206 X0.00 Y0.00 Z0.00
19:11:56.386 : echo:Auto Bed Leveling:
19:11:56.395 : echo: M420 S0 Z0.01
19:11:56.396 : echo:PID settings:
19:11:56.413 : echo: M301 P21.60 I1.25 D93.33
19:11:56.413 : echo:Z-Probe Offset (mm):
19:11:56.418 : echo: M851 Z-0.40